Questo contenuto non è disponibile nella lingua selezionata.

Chapter 10. OpenShift SDN network plugin


10.1. Enabling multicast for a project

10.1.1. About multicast

With IP multicast, data is broadcast to many IP addresses simultaneously.

Important
  • At this time, multicast is best used for low-bandwidth coordination or service discovery and not a high-bandwidth solution.
  • By default, network policies affect all connections in a namespace. However, multicast is unaffected by network policies. If multicast is enabled in the same namespace as your network policies, it is always allowed, even if there is a deny-all network policy. Cluster administrators should consider the implications to the exemption of multicast from network policies before enabling it.

Multicast traffic between Red Hat OpenShift Service on AWS pods is disabled by default. If you are using the OVN-Kubernetes network plugin, you can enable multicast on a per-project basis.

10.1.2. Enabling multicast between pods

You can enable multicast between pods for your project.

Prerequisites

  • Install the OpenShift CLI (oc).
  • You must log in to the cluster with a user that has the cluster-admin or the dedicated-admin role.

Procedure

  • Run the following command to enable multicast for a project. Replace <namespace> with the namespace for the project you want to enable multicast for.

    $ oc annotate namespace <namespace> \
        k8s.ovn.org/multicast-enabled=true
    Tip

    You can alternatively apply the following YAML to add the annotation:

    apiVersion: v1
    kind: Namespace
    metadata:
      name: <namespace>
      annotations:
        k8s.ovn.org/multicast-enabled: "true"

Verification

To verify that multicast is enabled for a project, complete the following procedure:

  1. Change your current project to the project that you enabled multicast for. Replace <project> with the project name.

    $ oc project <project>
  2. Create a pod to act as a multicast receiver:

    $ cat <<EOF| oc create -f -
    apiVersion: v1
    kind: Pod
    metadata:
      name: mlistener
      labels:
        app: multicast-verify
    spec:
      containers:
        - name: mlistener
          image: registry.access.redhat.com/ubi9
          command: ["/bin/sh", "-c"]
          args:
            ["dnf -y install socat hostname && sleep inf"]
          ports:
            - containerPort: 30102
              name: mlistener
              protocol: UDP
    EOF
  3. Create a pod to act as a multicast sender:

    $ cat <<EOF| oc create -f -
    apiVersion: v1
    kind: Pod
    metadata:
      name: msender
      labels:
        app: multicast-verify
    spec:
      containers:
        - name: msender
          image: registry.access.redhat.com/ubi9
          command: ["/bin/sh", "-c"]
          args:
            ["dnf -y install socat && sleep inf"]
    EOF
  4. In a new terminal window or tab, start the multicast listener.

    1. Get the IP address for the Pod:

      $ POD_IP=$(oc get pods mlistener -o jsonpath='{.status.podIP}')
    2. Start the multicast listener by entering the following command:

      $ oc exec mlistener -i -t -- \
          socat UDP4-RECVFROM:30102,ip-add-membership=224.1.0.1:$POD_IP,fork EXEC:hostname
  5. Start the multicast transmitter.

    1. Get the pod network IP address range:

      $ CIDR=$(oc get Network.config.openshift.io cluster \
          -o jsonpath='{.status.clusterNetwork[0].cidr}')
    2. To send a multicast message, enter the following command:

      $ oc exec msender -i -t -- \
          /bin/bash -c "echo | socat STDIO UDP4-DATAGRAM:224.1.0.1:30102,range=$CIDR,ip-multicast-ttl=64"

      If multicast is working, the previous command returns the following output:

      mlistener
Red Hat logoGithubRedditYoutubeTwitter

Formazione

Prova, acquista e vendi

Community

Informazioni sulla documentazione di Red Hat

Aiutiamo gli utenti Red Hat a innovarsi e raggiungere i propri obiettivi con i nostri prodotti e servizi grazie a contenuti di cui possono fidarsi.

Rendiamo l’open source più inclusivo

Red Hat si impegna a sostituire il linguaggio problematico nel codice, nella documentazione e nelle proprietà web. Per maggiori dettagli, visita ilBlog di Red Hat.

Informazioni su Red Hat

Forniamo soluzioni consolidate che rendono più semplice per le aziende lavorare su piattaforme e ambienti diversi, dal datacenter centrale all'edge della rete.

© 2024 Red Hat, Inc.