이 콘텐츠는 선택한 언어로 제공되지 않습니다.
1.14. Changing the Read/Write State of an Online Logical Unit
Certain storage devices provide the user with the ability to change the state of the device from Read/Write (R/W) to Read-Only (RO), and from RO to R/W. This is typically done through a management interface on the storage device. The operating system will not automatically update its view of the state of the device when a change is made. Follow the procedures described in this chapter to make the operating system aware of the change.
Run the following command, replacing XYZ with the desired device designator, to determine the operating system's current view of the R/W state of a device:
# blockdev --getro /dev/sdXYZ
The following command is also available for Red Hat Enterprise Linux 6:
# cat /sys/block/sdXYZ/ro 1 = read-only 0 = read-write
When using multipath, refer to the ro or rw field in the second line of output from the
multipath -ll command. For example:
36001438005deb4710000500000640000 dm-8 GZ,GZ500 [size=20G][features=0][hwhandler=0][ro] \_ round-robin 0 [prio=200][active] \_ 6:0:4:1 sdax 67:16 [active][ready] \_ 6:0:5:1 sday 67:32 [active][ready] \_ round-robin 0 [prio=40][enabled] \_ 6:0:6:1 sdaz 67:48 [active][ready] \_ 6:0:7:1 sdba 67:64 [active][ready]
To change the R/W state, use the following procedure:
Procedure 1.5. Change the R/W state
- To move the device from RO to R/W, see step 2.To move the device from R/W to RO, ensure no further writes will be issued. Do this by stopping the application, or through the use of an appropriate, application-specific action.Ensure that all outstanding write I/Os are complete with the following command:
# blockdev -flushbufs /dev/deviceReplace device with the desired designator; for a device mapper multipath, this is the entry for your device indev/mapper. For example,/dev/mapper/mpath3. - Use the management interface of the storage device to change the state of the logical unit from R/W to RO, or from RO to R/W. The procedure for this differs with each array. Consult applicable storage array vendor documentation for more information.
- Perform a re-scan of the device to update the operating system's view of the R/W state of the device. If using a device mapper multipath, perform this re-scan for each path to the device before issuing the command telling multipath to reload its device maps.This process is explained in further detail in Section 1.14.1, “Rescanning logical units”.
1.14.1. Rescanning logical units
After modifying the online logical unit Read/Write state, as described in Section 1.14, “Changing the Read/Write State of an Online Logical Unit”, re-scan the logical unit to ensure the system detects the updated state with the following command:
# echo 1 > /sys/block/sdX/device/rescan
To re-scan logical units on a system that uses multipathing, execute the above command for each sd device that represents a path for the multipathed logical unit. For example, run the command on sd1, sd2 and all other sd devices. To determine which devices are paths for a multipath unit, use
multipath -11, then find the entry that matches the logical unit to be changed.
Example 1.1. Use of the multipath -11 command
For example, the
multipath -11 above shows the path for the LUN with WWID 36001438005deb4710000500000640000. In this case, enter:
# echo 1 > /sys/block/sdax/device/rescan# echo 1 > /sys/block/sday/device/rescan# echo 1 > /sys/block/sdaz/device/rescan# echo 1 > /sys/block/sdba/device/rescan
