Red Hat Summit Red Hat Summit지원콘솔개발자평가판 시작연락처

이 콘텐츠는 선택한 언어로 제공되지 않습니다.

10.9. Example - Setting up Cascading Geo-replication

This section provides step by step instructions to set up a cascading geo-replication session. The configuration of this example has three volumes and the volume names are master-vol, interimmaster-vol, and slave-vol.
  1. Verify that your environment matches the minimum system requirements listed in Section 10.3.3, “Prerequisites”.
  2. Determine the appropriate deployment scenario. For more information on deployment scenarios, see Section 10.3.1, “Exploring Geo-replication Deployment Scenarios”.
  3. Configure the environment and create a geo-replication session between master-vol and interimmaster-vol.
    1. Create a common pem pub file, run the following command on the master node where the passwordless SSH connection is configured: 
      # gluster system:: execute gsec_create
      Copy to Clipboard Toggle word wrap
    2. Create the geo-replication session using the following command. The push-pem option is needed to perform the necessary pem-file setup on the interimmaster nodes. 
      # gluster volume geo-replication master-vol interimhost.com::interimmaster-vol create
push-pem
      Copy to Clipboard Toggle word wrap
    3. Verify the status of the created session by running the following command: 
      # gluster volume geo-replication master-vol interimhost::interimmaster-vol status
      Copy to Clipboard Toggle word wrap
  4. Configure the meta-volume for geo-replication: 
    # gluster volume geo-replication master-vol interimhost.com::interimmaster-vol config use_meta_volume true
    Copy to Clipboard Toggle word wrap
    For more information on configuring meta-volume, see Section 10.3.5, “Configuring a Meta-Volume”.
  5. Start a Geo-replication session between the hosts: 
    # gluster volume geo-replication master-vol interimhost.com::interimmaster-vol start
    Copy to Clipboard Toggle word wrap
    This command will start distributed geo-replication on all the nodes that are part of the master volume. If a node that is part of the master volume is down, the command will still be successful. In a replica pair, the geo-replication session will be active on any of the replica nodes, but remain passive on the others. After executing the command, it may take a few minutes for the session to initialize and become stable.
  6. Verifying the status of geo-replication session by running the following command: 
    # gluster volume geo-replication master-vol interimhost.com::interimmaster-vol status
    Copy to Clipboard Toggle word wrap
  7. Create a geo-replication session between interimmaster-vol and slave-vol.
    1. Create a common pem pub file by running the following command on the interimmaster master node where the passwordless SSH connection is configured: 
      # gluster system:: execute gsec_create
      Copy to Clipboard Toggle word wrap
    2. On interimmaster node, create the geo-replication session using the following command. The push-pem option is needed to perform the necessary pem-file setup on the slave nodes. 
      # gluster volume geo-replication interimmaster-vol slave_host.com::slave-vol create push-pem
      Copy to Clipboard Toggle word wrap
    3. Verify the status of the created session by running the following command: 
      # gluster volume geo-replication interrimmaster-vol slave_host::slave-vol status
      Copy to Clipboard Toggle word wrap
  8. Configure the meta-volume for geo-replication: 
    # gluster volume geo-replication interrimmaster-vol slave_host::slave-vol config use_meta_volume true
    Copy to Clipboard Toggle word wrap
    For more information on configuring meta-volume, see Section 10.3.5, “Configuring a Meta-Volume”.
  9. Start a geo-replication session between interrimaster-vol and slave-vol by running the following command: 
    # gluster volume geo-replication interrimmaster-vol slave_host.com::slave-vol start
    Copy to Clipboard Toggle word wrap
  10. Verify the status of geo-replication session by running the following: 
    # gluster volume geo-replication interrimmaster-vol slave_host.com::slave-vol status
    Copy to Clipboard Toggle word wrap
맨 위로 이동
Red Hat logoGithubredditYoutubeTwitter

자세한 정보

평가판, 구매 및 판매

커뮤니티

Red Hat 문서 정보

Red Hat을 사용하는 고객은 신뢰할 수 있는 콘텐츠가 포함된 제품과 서비스를 통해 혁신하고 목표를 달성할 수 있습니다. 최신 업데이트를 확인하세요.

보다 포괄적 수용을 위한 오픈 소스 용어 교체

Red Hat은 코드, 문서, 웹 속성에서 문제가 있는 언어를 교체하기 위해 최선을 다하고 있습니다. 자세한 내용은 다음을 참조하세요.Red Hat 블로그.

Red Hat 소개

Red Hat은 기업이 핵심 데이터 센터에서 네트워크 에지에 이르기까지 플랫폼과 환경 전반에서 더 쉽게 작업할 수 있도록 강화된 솔루션을 제공합니다.

Theme

© 2025 Red Hat