Red Hat Summit 红帽全球峰会支持控制台（Console）开发人员开始试用联系人

15.6. Increasing the ring buffer size to reduce a high packet drop rate by using the network RHEL system role

Increase the size of an Ethernet device’s ring buffers if the packet drop rate causes applications to report a loss of data, timeouts, or other issues.

Ring buffers are circular buffers where an overflow overwrites existing data. The network card assigns a transmit (TX) and receive (RX) ring buffer. Receive ring buffers are shared between the device driver and the network interface controller (NIC). Data can move from NIC to the kernel through either hardware interrupts or software interrupts, also called SoftIRQs.

The kernel uses the RX ring buffer to store incoming packets until the device driver can process them. The device driver drains the RX ring, typically by using SoftIRQs, which puts the incoming packets into a kernel data structure called an sk_buff or skb to begin its journey through the kernel and up to the application that owns the relevant socket.

The kernel uses the TX ring buffer to hold outgoing packets which should be sent to the network. These ring buffers reside at the bottom of the stack and are a crucial point at which packet drop can occur, which in turn will adversely affect network performance.

You configure ring buffer settings in the NetworkManager connection profiles. By using Ansible and the network RHEL system role, you can automate this process and remotely configure connection profiles on the hosts defined in a playbook.

警告

You cannot use the network RHEL system role to update only specific values in an existing connection profile. The role ensures that a connection profile exactly matches the settings in a playbook. If a connection profile with the same name already exists, the role applies the settings from the playbook and resets all other settings in the profile to their defaults. To prevent resetting values, always specify the whole configuration of the network connection profile in the playbook, including the settings that you do not want to change.

Prerequisites

  • You have prepared the control node and the managed nodes.
  • You are logged in to the control node as a user who can run playbooks on the managed nodes.
  • The account you use to connect to the managed nodes has sudo permissions for these nodes.
  • You know the maximum ring buffer sizes that the device supports.

Procedure

  1. Create a playbook file, for example, ~/playbook.yml, with the following content: 

    ---
- name: Configure the network
  hosts: managed-node-01.example.com
  tasks:
    - name: Ethernet connection profile with dynamic IP address setting and increased ring buffer sizes
      ansible.builtin.include_role:
        name: redhat.rhel_system_roles.network
      vars:
        network_connections:
          - name: enp1s0
            type: ethernet
            autoconnect: yes
            ip:
              dhcp4: yes
              auto6: yes
            ethtool:
              ring:
                rx: 4096
                tx: 4096
            state: up

    The settings specified in the example playbook include the following:

    rx: <value>
    Sets the maximum number of received ring buffer entries.
    tx: <value>
    Sets the maximum number of transmitted ring buffer entries.

    For details about all variables used in the playbook, see the /usr/share/ansible/roles/rhel-system-roles.network/README.md file on the control node.

  2. Validate the playbook syntax: 

    $ ansible-playbook --syntax-check ~/playbook.yml

    Note that this command only validates the syntax and does not protect against a wrong but valid configuration.

  3. Run the playbook: 

    $ ansible-playbook ~/playbook.yml

Verification

  • Display the maximum ring buffer sizes: 

    # ansible managed-node-01.example.com -m command -a 'ethtool -g enp1s0'
managed-node-01.example.com | CHANGED | rc=0 >>
...
Current hardware settings:
RX:             4096
RX Mini:        0
RX Jumbo:       0
TX:             4096
Red Hat logoGithubredditYoutubeTwitter

学习

尝试、购买和销售

社区

关于红帽文档

通过我们的产品和服务，以及可以信赖的内容，帮助红帽用户创新并实现他们的目标。 了解我们当前的更新.

让开源更具包容性

红帽致力于替换我们的代码、文档和 Web 属性中存在问题的语言。欲了解更多详情，请参阅红帽博客.

關於紅帽

我们提供强化的解决方案，使企业能够更轻松地跨平台和环境（从核心数据中心到网络边缘）工作。

Theme

© 2026 Red Hat返回顶部