5.4.16. RAID Logical Volumes

To create a RAID logical volume, you specify a raid type as the --type argument of the lvcreate command. Usually when you create a logical volume with the lvcreate command, the --type argument is implicit. For example, when you specify the -i stripes argument, the lvcreate command assumes the --type stripe option. When you specify the -m mirrors argument, the lvcreate command assumes the --type mirror option. When you create a RAID logical volume, however, you must explicitly specify the segment type you desire. The possible RAID segment types are described in Table 5.1, “RAID Segment Types”.

For most users, specifying one of the five available primary types (raid1, raid4, raid5, raid6, raid10) should be sufficient. For more information on the different algorithms used by RAID 5/6, see chapter four of the Common RAID Disk Data Format Specification at http://www.snia.org/sites/default/files/SNIA_DDF_Technical_Position_v2.0.pdf.

When you create a RAID logical volume, LVM creates a metadata subvolume that is one extent in size for every data or parity subvolume in the array. For example, creating a 2-way RAID1 array results in two metadata subvolumes (lv_rmeta_0 and lv_rmeta_1) and two data subvolumes (lv_rimage_0 and lv_rimage_1). Similarly, creating a 3-way stripe (plus 1 implicit parity device) RAID4 results in 4 metadata subvolumes (lv_rmeta_0, lv_rmeta_1, lv_rmeta_2, and lv_rmeta_3) and 4 data subvolumes (lv_rimage_0, lv_rimage_1, lv_rimage_2, and lv_rimage_3).

The following command creates a 2-way RAID1 array named my_lv in the volume group my_vg that is 1G in size.

# lvcreate --type raid1 -m 1 -L 1G -n my_lv my_vg

You can create RAID1 arrays with different numbers of copies according to the value you specify for the -m argument. Although the -m argument is the same argument used to specify the number of copies for the previous mirror implementation, in this case you override the default segment type mirror by explicitly setting the segment type as raid1. Similarly, you specify the number of stripes for a RAID 4/5/6 logical volume with the familiar -i argument, overriding the default segment type with the desired RAID type. You can also specify the stripe size with the -I argument.

The following command creates a RAID5 array (3 stripes + 1 implicit parity drive) named my_lv in the volume group my_vg that is 1G in size. Note that you specify the number of stripes just as you do for an LVM striped volume; the correct number of parity drives is added automatically.

# lvcreate --type raid5 -i 3 -L 1G -n my_lv my_vg

The following command creates a RAID6 array (3 stripes + 2 implicit parity drives) named my_lv in the volume group my_vg that is 1G in size.

# lvcreate --type raid6 -i 3 -L 1G -n my_lv my_vg

After you have created a RAID logical volume with LVM, you can activate, change, remove, display, and use the volume just as you would any other LVM logical volume.

When you create RAID10 logical volumes, the background I/O required to initialize the logical volumes with a sync operation can crowd out other I/O operations to LVM devices, such as updates to volume group metadata, particularly when you are creating many RAID logical volumes. This can cause the other LVM operations to slow down.

As of Red Hat Enterprise Linux 6.5, you can control the rate at which a RAID logical volume is initialized by implementing recovery throttling. You control the rate at which sync operations are performed by setting the minimum and maximum I/O rate for those operations with the --minrecoveryrate and --maxrecoveryrate options of the lvcreate command. You specify these options as follows.

The following command creates a 2-way RAID10 array with 3 stripes that is 10G is size with a maximum recovery rate of 128 kiB/sec/device. The array is named my_lv and is in the volume group my_vg.

lvcreate --type raid10 -i 2 -m 1 -L 10G --maxrecoveryrate 128 -n my_lv my_vg

You can also specify minimum and maximum recovery rates for a RAID scrubbing operation. For information on RAID scrubbing, see Section 5.4.16.10, “Scrubbing a RAID Logical Volume”.