Chapter 18. iptables
Included with Red Hat Enterprise Linux are advanced tools for network packet filtering — the process of controlling network packets as they enter, move through, and exit the network stack within the kernel. Kernel versions prior to 2.4 relied on
ipchains for packet filtering and used lists of rules applied to packets at each step of the filtering process. The introduction of the 2.4 kernel brought with it iptables (also called netfilter), which is similar to ipchains but greatly expands the scope and control available for filtering network packets.
This chapter focuses on packet filtering basics, defines the differences between
ipchains and iptables, explains various options available with iptables commands, and explains how filtering rules can be preserved between system reboots.
For instructions on constructing
iptables rules or setting up a firewall based on these rules, refer to Section 18.7, “Additional Resources”.
Warning
The default firewall mechanism under the 2.4 and newer kernels is
iptables, but iptables cannot be used if ipchains are already running. If ipchains is present at boot time, the kernel issues an error and fails to start iptables.
The functionality of
ipchains is not affected by these errors.
18.1. Packet Filtering
The Linux kernel has the built-in ability to filter packets, allowing some of them to be received by or pass through the system while stopping others. The kernel's netfilter has three built-in tables or rules lists. They are as follows:
filter— The default table for handling network packets.nat— Used to alter packets that create a new connection and used for Network Address Translation (NAT).mangle— Used for specific types of packet alteration.
Note
In addition to these built in tables, specialized tables can be created and stored in the
/lib/modules/<kernel-version>/kernel/net/ipv4/netfilter/ directory (where <kernel-version> corresponds to the version kernel number).
Each table has a group of built-in chains which correspond to the actions performed on the packet by the netfilter.
The built-in chains for the
filter table are as follows:
- INPUT — Applies to network packets that are targeted for the host.
- OUTPUT — Applies to locally-generated network packets.
- FORWARD — Applies to network packets routed through the host.
The built-in chains for the
nat table are as follows:
- PREROUTING — Alters network packets when they arrive.
- OUTPUT — Alters locally-generated network packets before they are sent out.
- POSTROUTING — Alters network packets before they are sent out.
The built-in chains for the
mangle table are as follows:
- INPUT — Alters network packets targeted for the host.
- OUTPUT — Alters locally-generated network packets before they are sent out.
- FORWARD — Alters network packets routed through the host.
- PREROUTING — Alters incoming network packets before they are routed.
- POSTROUTING — Alters network packets before they are sent out.
Every network packet received by or sent from a Linux system is subject to at least one table. However, a packet may be subjected to multiple rules within each table before emerging at the end of the chain. The structure and purpose of these rules may vary, but they usually seek to identify a packet coming from or going to a particular IP address, or set of addresses, when using a particular protocol and network service.
Note
Do not use fully qualified domain names in firewall rules that are saved in the
/etc/sysconfig/iptables or /etc/sysconfig/ip6tables files. In the following example: iptables -A FORWARD -s example.com -i eth0 -j DROP example.com is invalid because the iptables service starts before any DNS related services at boot time, which results in an error. Only IP addresses are valid in creating firewall rules.
Regardless of their destination, when packets match a particular rule in one of the tables, a target or action is applied to them. If the rule specifies an
ACCEPT target for a matching packet, the packet skips the rest of the rule checks and is allowed to continue to its destination. If a rule specifies a DROP target, that packet is refused access to the system and nothing is sent back to the host that sent the packet. If a rule specifies a QUEUE target, the packet is passed to user-space. If a rule specifies the optional REJECT target, the packet is dropped, but an error packet is sent to the packet's originator.
Every chain has a default policy to
ACCEPT, DROP, REJECT, or QUEUE. If none of the rules in the chain apply to the packet, then the packet is dealt with in accordance with the default policy.
The
iptables command configures these tables, as well as sets up new tables if necessary.
