検索

このコンテンツは選択した言語では利用できません。

4.156. lldpad

download PDF
An updated lldpad package that fixes several bugs and adds various enhancements is now available for Red Hat Enterprise Linux 6.
The lldpad package provides the Linux user space daemon and configuration tool for Intel's Link Layer Discovery Protocol (LLDP) agent with Enhanced Ethernet support.
The lldpad package has been upgraded to upstream version 0.9.43, which provides a number of bug fixes and enhancements over the previous version. (BZ#731407)

Bug Fixes

BZ#749057
The Brocade 8000 Fibre Channel Forwarder (FCF) switch with FabOs 6.4.2b failed to process the CEE TLV frame on fabric session startup (started by the llpad). As a consequence, the Brocade 8000 Fibre Channel Forwarder (FCF) switch with FabOs 6.4.2b terminated the connection and subsequent fabric logins failed when IEEE 802.1Qaz DCBX was enabled. With this update, the llptool utility can configure lldpad not to use the CEE TLV frame for the fabric session initiation (for the eth3 device, the initiator should issue the "lldptool -T -i eth3 -V IEEE-DCBX mode=reset" command) and the problem no longer occurs.
BZ#694639
The lldpad service triggered excessive timeout events every second. This caused the service to consume excess resources. Now, the lldpad service has been switched from polling-based to a demand-based model. This prevents excessive timeout event generation and ensures that the service consumes only the expected resources.
BZ#733123
The lldpad utility did not detect the maximum number of traffic classes supported by a device correctly. This resulted in an invalid or incorrect hardware configuration. Now, the utility detects the maximum number of traffic classes correctly.
BZ#720825, BZ#744133
The Edge Control Protocol (ECP) could not verify whether a port lookup was successful when running Virtual Discovery and Configuration Protocol (VDP) on bonded devices because VDP does not support bonded devices. As a consequence, the LLDP agent terminated unexpectedly with a segmentation fault. With this update, VDP is no longer initialized on bonded devices and the crash no longer occurs.
BZ#647211
The lldpad utility failed to initialize correctly on the Intel 82599ES 10 Gigabit Ethernet Controller (Niantic) with virtual functions enabled and returned a message that there were too many neighbors. With this update, lldpad initializes correctly and the problem no longer occurs.
BZ#735313
Prior to this update, a user with non-superuser permissions could start the lldpad service. With this update the lldpad init scripts have been modified and a user with non-superuser permissions can no longer start the service.
BZ#683837
The init script did not perform a line feed when returning the output of a service command. With this update, the init script has been recoded and the output of the service command is correct.
BZ#720730
The get_bcn() function returned without freeing the nlh variable, which caused a memory leak. The function has been modified and the memory leak no longer occurs.
BZ#741359
The lldpad daemon failed to detect that a NIC (Network Interface Card) had the offloaded DCBX (Data Center Bridging eXchange) stack implemented in its firmware. As a consequence, the lldp packets were send by both, the daemon and the NIC. With this update, the lldpad daemon no longer sends the packets if a NIC driver implements the offloaded DCBX stack.
BZ#749943
The lldpad utility incorrectly accessed memory. With this update, the utility accesses the memory correctly.

Enhancement

BZ#695550
The lldpad package now supports the 802.1Qaz standard (Enhanced Transmission Selection for Bandwidth Sharing Between Traffic Classes).
Users are advised to upgrade to this updated lldpad package, which fixes these bugs and adds these enhancements.
Updated lldpad packages that fix one bug are now available for Red Hat Enterprise Linux 6.
The lldpad packages provides the Linux user space daemon and configuration tool for Intel's Link Layer Discovery Protocol (LLDP) agent with Enhanced Ethernet support.

Bug Fix

BZ#822377
The lldpad tool is initially invoked by initrd during the boot process to support Fibre Channel over Ethernet (FCoE) boot from a Storage Area Network (SAN). The runtime lldpad init script did not kill lldpad before restarting it after system boot. Consequently, lldpad could not be started normally after system boot. With this update, the lldpad init script now contains the "-k" option to terminate the first instance of lldpad that was started during system boot.
All users of lldpad are advised to upgrade to these updated packages, which fix this bug.
Updated lldpad packages that fix one bug are now available for Red Hat Enterprise Linux 6.
The lldpad packages provide the Linux user space daemon and configuration tool for Intel's Link Layer Discovery Protocol (LLDP) agent with Enhanced Ethernet support.

Bug Fix

BZ#828683
Previously, dcbtool commands could, under certain circumstances, fail to enable the Fibre Channel over Ethernet (FCoE) application type-length-values (TLV) for a selected interface during the installation process. Consequently, various important features might have not been enabled (for example priority flow control, or PFC) by the Data Center Bridging eXchange (DCBX) peer. To prevent such problems, application-specific parameters (such as the FCoE application TLV) in DCBX are now enabled by default.
All users of lldpad are advised to upgrade to these updated packages, which fix this bug.
Red Hat logoGithubRedditYoutubeTwitter

詳細情報

試用、購入および販売

コミュニティー

Red Hat ドキュメントについて

Red Hat をお使いのお客様が、信頼できるコンテンツが含まれている製品やサービスを活用することで、イノベーションを行い、目標を達成できるようにします。

多様性を受け入れるオープンソースの強化

Red Hat では、コード、ドキュメント、Web プロパティーにおける配慮に欠ける用語の置き換えに取り組んでいます。このような変更は、段階的に実施される予定です。詳細情報: Red Hat ブログ.

会社概要

Red Hat は、企業がコアとなるデータセンターからネットワークエッジに至るまで、各種プラットフォームや環境全体で作業を簡素化できるように、強化されたソリューションを提供しています。

© 2024 Red Hat, Inc.