검색

이 콘텐츠는 선택한 언어로 제공되지 않습니다.

3.5. Configuring Fence Devices

download PDF
Configuring fence devices consists of creating, modifying, and deleting fence devices. Creating a fence device consists of selecting a fence device type and entering parameters for that fence device (for example, name, IP address, login, and password). Modifying a fence device consists of selecting an existing fence device and changing parameters for that fence device. Deleting a fence device consists of selecting an existing fence device and deleting it.

Note

If you are creating a new cluster, you can create fence devices when you configure cluster nodes. Refer to Section 3.6, “Configuring Cluster Members”.
With Conga you can create shared and non-shared fence devices.
The following shared fence devices are available:
  • APC Power Switch
  • Brocade Fabric Switch
  • Bull PAP
  • Egenera SAN Controller
  • GNBD
  • IBM Blade Center
  • McData SAN Switch
  • QLogic SANbox2
  • SCSI Fencing
  • Virtual Machine Fencing
  • Vixel SAN Switch
  • WTI Power Switch
The following non-shared fence devices are available:
  • Dell DRAC
  • HP iLO
  • IBM RSA II
  • IPMI LAN
  • RPS10 Serial Switch
This section provides procedures for the following tasks:
The starting point of each procedure is at the cluster-specific page that you navigate to from Choose a cluster to administer displayed on the cluster tab.

3.5.1. Creating a Shared Fence Device

To create a shared fence device, follow these steps:
  1. At the detailed menu for the cluster (below the clusters menu), click Shared Fence Devices. Clicking Shared Fence Devices causes the display of the fence devices for a cluster and causes the display of menu items for fence device configuration: Add a Fence Device and Configure a Fence Device.

    Note

    If this is an initial cluster configuration, no fence devices have been created, and therefore none are displayed.
  2. Click Add a Fence Device. Clicking Add a Fence Device causes the Add a Sharable Fence Device page to be displayed (refer to Figure 3.1, “Fence Device Configuration”).
    Fence Device Configuration

    Figure 3.1. Fence Device Configuration

  3. At the Add a Sharable Fence Device page, click the drop-down box under Fencing Type and select the type of fence device to configure.
  4. Specify the information in the Fencing Type dialog box according to the type of fence device. Refer to Appendix B, Fence Device Parameters for more information about fence device parameters.
  5. Click Add this shared fence device.
  6. Clicking Add this shared fence device causes a progress page to be displayed temporarily. After the fence device has been added, the detailed cluster properties menu is updated with the fence device under Configure a Fence Device.
Red Hat logoGithubRedditYoutubeTwitter

자세한 정보

평가판, 구매 및 판매

커뮤니티

Red Hat 문서 정보

Red Hat을 사용하는 고객은 신뢰할 수 있는 콘텐츠가 포함된 제품과 서비스를 통해 혁신하고 목표를 달성할 수 있습니다.

보다 포괄적 수용을 위한 오픈 소스 용어 교체

Red Hat은 코드, 문서, 웹 속성에서 문제가 있는 언어를 교체하기 위해 최선을 다하고 있습니다. 자세한 내용은 다음을 참조하세요.Red Hat 블로그.

Red Hat 소개

Red Hat은 기업이 핵심 데이터 센터에서 네트워크 에지에 이르기까지 플랫폼과 환경 전반에서 더 쉽게 작업할 수 있도록 강화된 솔루션을 제공합니다.

© 2024 Red Hat, Inc.