Red Hat Summit Red Hat SummitSuporteConsoleDesenvolvedoresComeçar um testeContato

Este conteúdo não está disponível no idioma selecionado.

10.4. Configure 802.1Q VLAN Tagging Using the Command Line

In Red Hat Enterprise Linux 7, the 8021q module is loaded by default. If necessary, you can make sure that the module is loaded by issuing the following command as root: 
~]# modprobe --first-time 8021q
modprobe: ERROR: could not insert '8021q': Module already in kernel
Copy to Clipboard Toggle word wrap
To display information about the module, issue the following command: 
~]$ modinfo 8021q
Copy to Clipboard Toggle word wrap
See the modprobe(8) man page for more command options.

10.4.1. Setting Up 802.1Q VLAN Tagging Using ifcfg Files
Copiar o link

  1. Configure the parent interface in /etc/sysconfig/network-scripts/ifcfg-device_name, where device_name is the name of the interface: 
    DEVICE=interface_name
TYPE=Ethernet
BOOTPROTO=none
ONBOOT=yes
    Copy to Clipboard Toggle word wrap
  2. Configure the VLAN interface configuration in the /etc/sysconfig/network-scripts/ directory. The configuration file name should be the parent interface plus a . character plus the VLAN ID number. For example, if the VLAN ID is 192, and the parent interface is enp1s0, then the configuration file name should be ifcfg-enp1s0.192: 
    DEVICE=enp1s0.192
BOOTPROTO=none
ONBOOT=yes
IPADDR=192.168.1.1
PREFIX=24
NETWORK=192.168.1.0
VLAN=yes
    Copy to Clipboard Toggle word wrap
    If there is a need to configure a second VLAN, with for example, VLAN ID 193, on the same interface, enp1s0, add a new file with the name enp1s0.193 with the VLAN configuration details.
  3. Restart the networking service in order for the changes to take effect. As root issue the following command: 
    ~]# systemctl restart network
    Copy to Clipboard Toggle word wrap

10.4.2. Configure 802.1Q VLAN Tagging Using ip Commands
Copiar o link

To create an 802.1Q VLAN interface on Ethernet interface enp1s0, with name VLAN8 and ID 8, issue a command as root as follows: 
~]# ip link add link enp1s0 name enp1s0.8 type vlan id 8
Copy to Clipboard Toggle word wrap
To view the VLAN, issue the following command: 
~]$ ip -d link show enp1s0.8
4: enp1s0.8@enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT
     link/ether 52:54:00:ce:5f:6c brd ff:ff:ff:ff:ff:ff promiscuity 0
     vlan protocol 802.1Q id 8 <REORDER_HDR>
Copy to Clipboard Toggle word wrap
Note that the ip utility interprets the VLAN ID as a hexadecimal value if it is preceded by 0x and as an octal value if it has a leading 0. This means that in order to assign a VLAN ID with a decimal value of 22, you must not add any leading zeros.
To remove the VLAN, issue a command as root as follows: 
~]# ip link delete enp1s0.8
Copy to Clipboard Toggle word wrap
To use multiple interfaces belonging to multiple VLANs, create locally enp1s0.1 and enp1s0.2 with the appropriate VLAN ID on top of a physical interface enp1s0: 
~]# ip link add link enp1s0 name enp1s0.1 type vlan id 1
    ip link set dev enp1s0.1 up
~]# ip link add link enp1s0 name enp1s0.2 type vlan id 2
    ip link set dev enp1s0.2 up
Copy to Clipboard Toggle word wrap
Note that running a network sniffer on a physical device, you can capture the tagged frames reaching the physical device, even if no VLAN device is configured on top of enp1s0. For example: 
tcpdump -nnei enp1s0 -vvv
Copy to Clipboard Toggle word wrap

Note

VLAN interfaces created using ip commands at the command prompt will be lost if the system is shutdown or restarted. To configure VLAN interfaces to be persistent after a system restart, use ifcfg files. See Section 10.4.1, “Setting Up 802.1Q VLAN Tagging Using ifcfg Files”
Voltar ao topo
Red Hat logoGithubredditYoutubeTwitter

Aprender

Experimente, compre e venda

Comunidades

Sobre a documentação da Red Hat

Ajudamos os usuários da Red Hat a inovar e atingir seus objetivos com nossos produtos e serviços com conteúdo em que podem confiar. Explore nossas atualizações recentes.

Tornando o open source mais inclusivo

A Red Hat está comprometida em substituir a linguagem problemática em nosso código, documentação e propriedades da web. Para mais detalhes veja o Blog da Red Hat.

Sobre a Red Hat

Fornecemos soluções robustas que facilitam o trabalho das empresas em plataformas e ambientes, desde o data center principal até a borda da rede.

Theme

© 2025 Red Hat