Red Hat Summit Red Hat SummitSuporteConsoleDesenvolvedoresComeçar um testeContato

Este conteúdo não está disponível no idioma selecionado.

7.3. Network Bonding Using the NetworkManager Command Line Tool, nmcli

Note

See Section 3.3, “Configuring IP Networking with nmcli” for an introduction to nmcli.
To create a bond connection with the nmcli tool, issue the following command: 
~]$ nmcli con add type bond ifname mybond0
Connection 'bond-mybond0' (5f739690-47e8-444b-9620-1895316a28ba) successfully added.
Copy to Clipboard Toggle word wrap
Note that as no con-name was given for the bond, the connection name was derived from the interface name by prepending the type.
NetworkManager supports most of the bonding options provided by the kernel. For example: 
~]$ nmcli con add type bond ifname mybond0 bond.options "mode=balance-rr,miimon=100"
Connection 'bond-mybond0' (5f739690-47e8-444b-9620-1895316a28ba) successfully added.
Copy to Clipboard Toggle word wrap
To add a port interface:
  1. Create a new connection, see Section 3.3.5, “Creating and Modifying a Connection Profile with nmcli” for details.
  2. Set the controller property to the bond interface name, or to the name of the controller connection: 
~]$ nmcli con add type ethernet ifname ens3 master mybond0
Connection 'bond-slave-ens3' (220f99c6-ee0a-42a1-820e-454cbabc2618) successfully added.
Copy to Clipboard Toggle word wrap
To add a new port interface, repeat the previous command with the new interface. For example: 
~]$ nmcli con add type ethernet ifname ens7 master mybond0
Connection 'bond-slave-ens7' (ecc24c75-1c89-401f-90c8-9706531e0231) successfully added.
Copy to Clipboard Toggle word wrap
To activate the ports, issue a command as follows: 
~]$ nmcli con up bond-slave-ens7
Connection successfully activated (D-Bus active path: /org/freedesktop/NetworkManager/ActiveConnection/14)
Copy to Clipboard Toggle word wrap 
~]$ nmcli con up bond-slave-ens3
Connection successfully activated (D-Bus active path: /org/freedesktop/NetworkManager/ActiveConnection/15)
Copy to Clipboard Toggle word wrap
When you activate a port, the controller connection also starts. You can see Section 7.1, “Understanding the Default Behavior of Controller and Port Interfaces” for more information. In this case, it is not necessary to manually activate the controller connection.
It is possible to change the active_slave option and the primary option of the bond at runtime, without deactivating the connection. For example to change the active_slave option, issue the following command: 
~]$ nmcli dev mod bond0 +bond.options "active_slave=ens7"
Connection successfully reapplied to device 'bond0'.
Copy to Clipboard Toggle word wrap
or to change the primary option: 
~]$ nmcli dev mod bond0 +bond.options "primary=ens3"
Connection successfully reapplied to device 'bond0'.
Copy to Clipboard Toggle word wrap

Note

The active_slave option sets the currently active port whereas the primary option of the bond specifies the active port to be automatically selected by kernel when a new port is added or a failure of the active port occurs.
Voltar ao topo
Red Hat logoGithubredditYoutubeTwitter

Aprender

Experimente, compre e venda

Comunidades

Sobre a documentação da Red Hat

Ajudamos os usuários da Red Hat a inovar e atingir seus objetivos com nossos produtos e serviços com conteúdo em que podem confiar. Explore nossas atualizações recentes.

Tornando o open source mais inclusivo

A Red Hat está comprometida em substituir a linguagem problemática em nosso código, documentação e propriedades da web. Para mais detalhes veja o Blog da Red Hat.

Sobre a Red Hat

Fornecemos soluções robustas que facilitam o trabalho das empresas em plataformas e ambientes, desde o data center principal até a borda da rede.

Theme

© 2025 Red Hat