Red Hat Summit 红帽全球峰会支持控制台（Console）开发人员开始试用联系人

此内容没有您所选择的语言版本。

Chapter 4. Adding Servers to the Trusted Storage Pool

A storage pool is a network of storage servers.
When the first server starts, the storage pool consists of that server alone. Adding additional storage servers to the storage pool is achieved using the probe command from a running, trusted storage server.

Important

Before adding servers to the trusted storage pool, you must ensure that the ports specified in Chapter 3, Verifying Port Access are open.
On Red Hat Enterprise Linux 7, enable the glusterFS firewall service in the active zones for runtime and permanent mode using the following commands:
To get a list of active zones, run the following command: 
# firewall-cmd --get-active-zones
Copy to Clipboard Toggle word wrap
To allow the firewall service in the active zones, run the following commands: 
# firewall-cmd --zone=zone_name --add-service=glusterfs 
# firewall-cmd --zone=zone_name --add-service=glusterfs --permanent
Copy to Clipboard Toggle word wrap
For more information about using firewalls, see section Using Firewalls in the Red Hat Enterprise Linux 7 Security Guide: https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/7/html/Security_Guide/sec-Using_Firewalls.html.

Note

When any two gluster commands are executed concurrently on the same volume, the following error is displayed:
Another transaction is in progress.
This behavior in the Red Hat Gluster Storage prevents two or more commands from simultaneously modifying a volume configuration, potentially resulting in an inconsistent state. Such an implementation is common in environments with monitoring frameworks such as the Red Hat Gluster Storage Console, Red Hat Enterprise Virtualization Manager, and Nagios. For example, in a four node Red Hat Gluster Storage Trusted Storage Pool, this message is observed when gluster volume status VOLNAME command is executed from two of the nodes simultaneously.

4.1. Adding Servers to the Trusted Storage Pool
复制链接

The gluster peer probe [server] command is used to add servers to the trusted server pool.

Note

Probing a node from lower version to a higher version of Red Hat Gluster Storage node is not supported.

Adding Three Servers to a Trusted Storage Pool

Create a trusted storage pool consisting of three storage servers, which comprise a volume.

Prerequisites

  • The glusterd service must be running on all storage servers requiring addition to the trusted storage pool. See Chapter 24, Starting and Stopping the glusterd service for service start and stop commands.
  • Server1, the trusted storage server, is started.
  • The host names of the target servers must be resolvable by DNS.
  1. Run gluster peer probe [server] from Server 1 to add additional servers to the trusted storage pool.

    Note

    • Self-probing Server1 will result in an error because it is part of the trusted storage pool by default.
    • All the servers in the Trusted Storage Pool must have RDMA devices if either RDMA or RDMA,TCP volumes are created in the storage pool. The peer probe must be performed using IP/hostname assigned to the RDMA device. 
    # gluster peer probe server2
Probe successful

# gluster peer probe server3
Probe successful

# gluster peer probe server4
Probe successful
    Copy to Clipboard Toggle word wrap
  2. Verify the peer status from all servers using the following command: 
    # gluster peer status
Number of Peers: 3

Hostname: server2
Uuid: 5e987bda-16dd-43c2-835b-08b7d55e94e5
State: Peer in Cluster (Connected)

Hostname: server3
Uuid: 1e0ca3aa-9ef7-4f66-8f15-cbc348f29ff7
State: Peer in Cluster (Connected)

Hostname: server4
Uuid: 3e0caba-9df7-4f66-8e5d-cbc348f29ff7
State: Peer in Cluster (Connected)
    Copy to Clipboard Toggle word wrap

Important

If the existing trusted storage pool has a geo-replication session, then after adding the new server to the trusted storage pool, perform the steps listed at Section 10.5, “Starting Geo-replication on a Newly Added Brick or Node”.
返回顶部
Red Hat logoGithubredditYoutubeTwitter

学习

尝试、购买和销售

社区

关于红帽文档

通过我们的产品和服务，以及可以信赖的内容，帮助红帽用户创新并实现他们的目标。 了解我们当前的更新.

让开源更具包容性

红帽致力于替换我们的代码、文档和 Web 属性中存在问题的语言。欲了解更多详情，请参阅红帽博客.

關於紅帽

我们提供强化的解决方案，使企业能够更轻松地跨平台和环境（从核心数据中心到网络边缘）工作。

Theme

© 2025 Red Hat