5.9. Creating Dispersed Volumes

download PDF
Dispersed volumes are based on erasure coding. Erasure coding (EC) is a method of data protection in which data is broken into fragments, expanded and encoded with redundant data pieces and stored across a set of different locations. This allows the recovery of the data stored on one or more bricks in case of failure. The number of bricks that can fail without losing data is configured by setting the redundancy count.
Dispersed volume requires less storage space when compared to a replicated volume. It is equivalent to a replicated pool of size two, but requires 1.5 TB instead of 2 TB to store 1 TB of data when the redundancy level is set to 2. In a dispersed volume, each brick stores some portions of data and parity or redundancy. The dispersed volume sustains the loss of data based on the redundancy level.


Dispersed volume configuration is supported only on JBOD storage. For more information, see Section 20.1.2, “JBOD”.
Illustration of a Dispersed Volume

Figure 5.7. Illustration of a Dispersed Volume

The data protection offered by erasure coding can be represented in simple form by the following equation: n = k + m. Here n is the total number of bricks, we would require any k bricks out of n bricks for recovery. In other words, we can tolerate failure up to any m bricks. With this release, the following configurations are supported:
  • 6 bricks with redundancy level 2 (4 + 2)
  • 10 bricks with redundancy level 2 (8 + 2)
  • 11 bricks with redundancy level 3 (8 + 3)
  • 12 bricks with redundancy level 4 (8 + 4)
  • 20 bricks with redundancy level 4 (16 + 4)
For optimal fault tolerance, create each brick on a separate server. Creating multiple bricks on a single server is supported, but the more bricks there are on a single server, the greater the risk to availability and consistency when that single server becomes unavailable.
Use gluster volume create to create different types of volumes, and gluster volume info to verify successful volume creation.


Red Hat recommends you to review the Dispersed Volume configuration recommendations explained in Section 5.9, “Creating Dispersed Volumes” before creating the Dispersed volume.
To Create a dispersed volume
  1. Run the gluster volume create command to create the dispersed volume.
    The syntax is # gluster volume create NEW-VOLNAME [disperse-data COUNT] [redundancy COUNT] [transport tcp | rdma | tcp,rdma] NEW-BRICK...
    The number of bricks required to create a disperse volume is the sum of disperse-data count and redundancy count.
    The disperse-data count option specifies the number of bricks that is part of the dispersed volume, excluding the count of the redundant bricks. For example, if the total number of bricks is 6 and redundancy-count is specified as 2, then the disperse-data count is 4 (6 - 2 = 4). If the disperse-data count option is not specified, and only the redundancy count option is specified, then the disperse-data count is computed automatically by deducting the redundancy count from the specified total number of bricks.
    Redundancy determines how many bricks can be lost without interrupting the operation of the volume. If redundancy count is not specified, based on the configuration it is computed automatically to the optimal value and a warning message is displayed.
    The default value for transport is tcp. Other options can be passed such as auth.allow or auth.reject. See Section 5.3, “About Encrypted Disk” for a full list of parameters.

    Example 5.11. Dispersed Volume with Six Storage Servers

    # gluster volume create test-volume disperse-data 4 redundancy 2 transport tcp server1:/rhgs1/brick1 server2:/rhgs2/brick2 server3:/rhgs3/brick3 server4:/rhgs4/brick4 server5:/rhgs5/brick5 server6:/rhgs6/brick6
    Creation of test-volume has been successful
    Please start the volume to access data.
  2. Run # gluster volume start VOLNAME to start the volume.
    # gluster volume start test-volume
    Starting test-volume has been successful


    The open-behind volume option is enabled by default. If you are accessing the dispersed volume using the SMB protocol, you must disable the open-behind volume option to avoid performance bottleneck on large file workload. Run the following command to disable open-behind volume option:
    # gluster volume set VOLNAME open-behind off
    For information on open-behind volume option, see Section 11.1, “Configuring Volume Options”
  3. Run gluster volume info command to optionally display the volume information.
Red Hat logoGithubRedditYoutubeTwitter


Try, buy, & sell


About Red Hat Documentation

We help Red Hat users innovate and achieve their goals with our products and services with content they can trust.

Making open source more inclusive

Red Hat is committed to replacing problematic language in our code, documentation, and web properties. For more details, see the Red Hat Blog.

About Red Hat

We deliver hardened solutions that make it easier for enterprises to work across platforms and environments, from the core datacenter to the network edge.

© 2024 Red Hat, Inc.