Este contenido no está disponible en el idioma seleccionado.
4.108. mkinitrd
Updated mkinitrd packages that fix one bug are now available for Red Hat Enterprise Linux 5.
The mkinitrd utility creates file system images for use as initial RAM disk (initrd) images.
Bug Fix
- BZ#753693
- Due to an incomplete regular expression in the code, the mkinitrd utility did not recognize multipath devices located in the /dev/mpath/ directory. As a consequence, the system could not boot if such a multipath device contained the root file system. With this update, the regular expression has been corrected, and mkinitrd now correctly recognizes multipath devices in the /dev/mpath/ directory.
All users of mkinitrd are advised to upgrade to these updated packages, which fix this bug.
Updated mkinitrd packages that fix multiple bugs are now available for Red Hat Enterprise Linux 5.
The mkinitrd utility creates the
initrd
file system image. The initrd
image is an initial RAM disk that is loaded by a boot loader before the Linux kernel is started.
Bug Fixes
- BZ#512892
- Previously, due to missing code in the mkinitrd script, if two or more RAID arrays of the same level were created during installation, the raid456.ko module was loaded for every array of the same level. The system continued to boot but error messages for the second and subsequent arrays were displayed as follows:
insmod: error inserting '/lib/raid456.ko': -1 File exists
With this update the code has been improved and the mkinitrd script no longer attempts to load duplicate modules. - BZ#529158
- Prior to this update, although the mkinitrd script included commands to setup a bonded connection, it did not configure the bonding mode first. Consequently, the bonded connection did not work and a host could not boot if the root partition on an iSCSI device was attached by a bonded channel. With this update, a patch has been applied to mkinitrd and hosts can now boot when their root partitions are on iSCSI devices attached by bonded connections.
- BZ#532207
- When probing for the root device, mkinitrd did not use the full device path for the root device when using
LABEL
-based mounts with iSCSI RAID arrays. Consequently, the following error message was logged when updating the kernel:/sbin/scsi_id: option requires an argument -- s
With this update, a patch has been applied to mkinitrd and the error messages are no longer generated in the scenario described. - BZ#593096
- Due to a regression, if the system's
lvm.conf
file had thecommand_names
orprefix
directives set, the output from lvm.static would be corrupted. With this update a patch has been applied to override the system settings while running mkinitrd and the initrd image created now has an uncorruptedlvm.conf
file. - BZ#602409
- Prior to this update, nash, the linuxrc image script interpreter, did not support the
dirsync
mount option forext3
file systems. Consequently, if thedirsync
option was used for the root file system in the file systems table (fstab
), the system did not boot. The following error message was logged:EXT3-fs: Unrecognized mount option "dirsync" or missing value
This update includes a patch to support thedirsync
option with the mount command and synchronous directory modifications can now be made while usingext3
file systems. - BZ#620699
- Due to a missing dependency, the dmraid package was not installed by default. Consequently, when running the mkinitrd command on IBM System/390 and IBM System z, the command failed and the following error message was displayed:
cp: cannot stat `/sbin/dmraid.static': No such file or directory
With this update, a requirement for dmraid has been added to the mkinitrd specification file (mkinitrd.spec
). Themkinitrd
command now works as expected on IBM System/390 and System z. - BZ#660731
- Due to a regression in libdhcp, netlink interface flags were misinterpreted as standard interface flags by nash when it processed the
network
command. Consequently, theDEBUG
,PROMISC
, andALLMULTI
flags were incorrectly enabled on network interfaces. The problem has been corrected in libdhcp and the mkinitrd spec file has been changed to require libdhcp-devel-1.20-12 or later. As a result, the incorrect flags are no longer set on the network interfaces. - BZ#679581
- Prior to this update, the grubby command line tool for updating bootloader config files, terminated unexpectedly with a segmentation fault when the command
grubby --info=ALL
was executed andgrub.conf
contained Windows boot definitions. With this update, a patch has been applied and grubby no longer crashes but returnsnon linux entry
in the scenario described. - BZ#696971
- Previously, setting an attribute for all kernel entries in a config file using the
--update-kernel=ALL
command directive worked only once. Subsequent use of the--update-kernel=ALL
command directive only updated the arguments for the first kernel entry found. With this update a patch has been applied and the problem no longer occurs in the scenario described. - BZ#700102
- The mkinitrd man page did not include
multipath
in its list of limitations for FIPS support. With this update, the man page entry for FIPS has been improved to say the following:/boot Must not be on multipath, nfs, dmraid or mdraid
- BZ#700592
- Prior to this update, after /sbin/init was executed the nash-hotplug process did not terminate itself and had to be terminated by a kill command in
/etc/rc.sysinit
. With this update, a patch has been applied to improve the code and nash-hotplug now exits when the parent process terminates. - BZ#744330
- Due to an incomplete regular expression in the code, the mkinitrd utility did not recognize multipath devices located in the
/dev/mpath/
directory. As a consequence, the system could not boot if such a multipath device contained the root file system. With this update, the regular expression has been corrected, and mkinitrd now correctly recognizes multipath devices in the/dev/mpath/
directory.
Users of mkinitrd should upgrade to these updated packages, which fix these bugs.