Red Hat Summit Red Hat SummitSupportConsoleDéveloppeursCommencer un essaiContact

Ce contenu n'est pas disponible dans la langue sélectionnée.

B.12. Guest is Unable to Start with Error: warning: could not open /dev/net/tun

Symptom
The guest virtual machine does not start after configuring a type='ethernet' (also known as 'generic ethernet') interface in the host system. An error appears either in libvirtd.log, /var/log/libvirt/qemu/name_of_guest.log, or in both, similar to the below message: 
warning: could not open /dev/net/tun: no virtual network emulation qemu-kvm: -netdev tap,script=/etc/my-qemu-ifup,id=hostnet0: Device 'tap' could not be initialized
Copy to Clipboard Toggle word wrap
Investigation
Use of the generic ethernet interface type (<interface type='ethernet'>) is discouraged, because using it requires lowering the level of host protection against potential security flaws in QEMU and its guests. However, it is sometimes necessary to use this type of interface to take advantage of some other facility that is not yet supported directly in libvirt. For example, openvswitch was not supported in libvirt until libvirt-0.9.11, so in older versions of libvirt, <interface type='ethernet'> was the only way to connect a guest to an openvswitch bridge.
However, if you configure a <interface type='ethernet'> interface without making any other changes to the host system, the guest virtual machine will not start successfully.
The reason for this failure is that for this type of interface, a script called by QEMU needs to manipulate the tap device. However, with type='ethernet' configured, in an attempt to lock down QEMU, libvirt and SELinux have put in place several checks to prevent this. (Normally, libvirt performs all of the tap device creation and manipulation, and passes an open file descriptor for the tap device to QEMU.)
Solution
Reconfigure the host system to be compatible with the generic ethernet interface.

Procedure B.4. Reconfiguring the host system to use the generic ethernet interface

  1. Set SELinux to permissive by configuring SELINUX=permissive in /etc/selinux/config: 
    # This file controls the state of SELinux on the system.
# SELINUX= can take one of these three values:
#       enforcing - SELinux security policy is enforced.
#       permissive - SELinux prints warnings instead of enforcing.
#       disabled - No SELinux policy is loaded.
SELINUX=permissive
# SELINUXTYPE= can take one of these two values:
#       targeted - Targeted processes are protected,
#       mls - Multi Level Security protection.
SELINUXTYPE=targeted
    Copy to Clipboard Toggle word wrap
  2. From a root shell, run the command setenforce permissive.
  3. In /etc/libvirt/qemu.conf add or edit the following lines: 
    clear_emulator_capabilities = 0
    Copy to Clipboard Toggle word wrap 
    user = "root"
    Copy to Clipboard Toggle word wrap 
    group = "root"
    Copy to Clipboard Toggle word wrap 
    cgroup_device_acl = [
        "/dev/null", "/dev/full", "/dev/zero",
        "/dev/random", "/dev/urandom",
        "/dev/ptmx", "/dev/kvm", "/dev/kqemu",
	"/dev/rtc", "/dev/hpet", "/dev/net/tun",
    Copy to Clipboard Toggle word wrap
  4. Restart libvirtd.

Important

Since each of these steps significantly decreases the host's security protections against QEMU guest domains, this configuration should only be used if there is no alternative to using <interface type='ethernet'>.

Note

For more information on SELinux, refer to the Red Hat Enterprise Linux 6 Security-Enhanced Linux User Guide.
Retour au début
Red Hat logoGithubredditYoutubeTwitter

Apprendre

Essayez, achetez et vendez

Communautés

À propos de la documentation Red Hat

Nous aidons les utilisateurs de Red Hat à innover et à atteindre leurs objectifs grâce à nos produits et services avec un contenu auquel ils peuvent faire confiance. Découvrez nos récentes mises à jour.

Rendre l’open source plus inclusif

Red Hat s'engage à remplacer le langage problématique dans notre code, notre documentation et nos propriétés Web. Pour plus de détails, consultez le Blog Red Hat.

À propos de Red Hat

Nous proposons des solutions renforcées qui facilitent le travail des entreprises sur plusieurs plates-formes et environnements, du centre de données central à la périphérie du réseau.

Theme

© 2025 Red Hat