第 32 章 Configuring a Fibre-Channel Over Ethernet Interface
Setting up and deploying a Fibre-channel over Ethernet (FCoE) interface requires two packages:
fcoe-utilslldpad
Once these packages are installed, perform the following procedure to enable FCoE over a virtual LAN (VLAN):
过程 32.1. Configuring an Ethernet interface to use FCoE
- Configure a new VLAN by copying an existing network script (e.g.
/etc/fcoe/cfg-eth0) to the name of the Ethernet device that supports FCoE. This will provide you with a default file to configure. Given that the FCoE device isethX, run:# cp /etc/fcoe/cfg-eth0 /etc/fcoe/cfg-ethX
Modify the contents ofcfg-ethXas necessary. Of note,DCB_REQUIREDshould be set tonofor networking interfaces that implement a hardware DCBX client. - If you want the device to automatically load during boot time, set
ONBOOT=yesin the corresponding/etc/sysconfig/network-scripts/ifcfg-ethXfile. For example, if the FCoE device is eth2, then edit/etc/sysconfig/network-scripts/ifcfg-eth2accordingly. - Start the data center bridging daemon (
dcbd) using the following command:# /etc/init.d/lldpad start
- For networking interfaces that implement a hardware DCBX client, skip this step and move on to the next.For interfaces that require a software DCBX client, enable data center bridging on the Ethernet interface using the following commands:
# dcbtool sc ethX dcb on
Then, enable FCoE on the Ethernet interface by running:# dcbtool sc ethX app:fcoe e:1
注意
These commands will only work if thedcbdsettings for the Ethernet interface were not changed. - Load the FCoE device now using:
# ifconfig ethX up
- Start FCoE using:
# service fcoe start
The FCoE device should appear shortly, assuming all other settings on the fabric are correct. To view configured FCoE devices, run:# fcoeadm -i
After correctly configuring the Ethernet interface to use FCoE, Red Hat recommends that you set FCoE and
lldpad to run at startup. To do so, use chkconfig, as in:
# chkconfig lldpad on
# chkconfig fcoe on
警告
Do not run software-based DCB or LLDP on CNAs that implement DCB.
Some Combined Network Adapters (CNAs) implement the Data Center Bridging (DCB) protocol in firmware. The DCB protocol assumes that there is just one originator of DCB on a particular network link. This means that any higher-level software implementation of DCB, or Link Layer Discovery Protocol (LLDP), must be disabled on CNAs that implement DCB.
32.1. Fibre-Channel over Ethernet (FCoE) Target Set up
In addition to mounting LUNs over FCoE, as described in 第 32 章 Configuring a Fibre-Channel Over Ethernet Interface, exporting LUNs to other machines over FCoE is also supported.
重要
Before proceeding, refer to 第 32 章 Configuring a Fibre-Channel Over Ethernet Interface and verify that basic FCoE set up is completed, and that
fcoeadm -i displays configured FCoE interfaces.
过程 32.2. Configure FCoE target
- Setting up an FCoE target requires the installation of the
fcoe-target-utilspackage, along with its dependencies.# yum install fcoe-target-utils - FCoE target support is based on the LIO kernel target and does not require a userspace daemon. However, it is still necessary to enable the fcoe-target service to load the needed kernel modules and maintain the configuration across reboots.
# service fcoe-target start# chkconfig fcoe-target on - Configuration of an FCoE target is performed using the
targetcliutility, rather than by editing a.confas may be expected. The settings are then saved so they may be restored if the system restarts.# targetclitargetcliis a hierarchical configuration shell. Moving between nodes in the shell usescd, andlsshows the contents at or below the current configuration node. To get more options, the commandhelpis also available. - Define the file, block device, or pass-through SCSI device to export as a backstore.
例 32.1. Example 1 of defining a device
/> backstores/block create example1 /dev/sda4This creates a backstore calledexample1that maps to the/dev/sda4block device.例 32.2. Example 2 of defining a device
/> backstores/fileio create example2 /srv/example2.img 100MThis creates a backstore calledexample2which maps to the given file. If the file does not exist, it will be created. File size may use K, M, or G abbreviations and is only needed when the backing file does not exist.注意
If the globalauto_cd_after_createoption is on (the default), executing a create command will change the current configuration node to the newly created object. This can be disabled withset global auto_cd_after_create=false. Returning to the root node is possible withcd /. - Create an FCoE target instance on an FCoE interface.
/> tcm_fc/ create 00:11:22:33:44:55:66:77If FCoE interfaces are present on the system, tab-completing aftercreatewill list available interfaces. If not, ensurefcoeadm -ishows active interfaces. - Map a backstore to the target instance.
例 32.3. Example of mapping a backstore to the target instance
/> cd tcm_fc/00:11:22:33:44:55:66:77/> luns/ create /backstores/fileio/example2 - Allow access to the LUN from an FCoE initiator.
/> acls/ create 00:99:88:77:66:55:44:33The LUN should now be accessible to that initiator. - Exit
targetcliby typingexitor entering ctrl+D.
Exiting
targetcli will save the configuration by default. However it may be explicitly saved with the saveconfig command.
Refer to the
targetcli manpage for more information.
