Questo contenuto non è disponibile nella lingua selezionata.

Chapter 34. Relax-and-Recover (ReaR)

When a software or hardware failure breaks the system, the system administrator faces three tasks to restore it to the fully functioning state on a new hardware environment:

booting a rescue system on the new hardware
replicating the original storage layout
restoring user and system files

Most backup software solves only the third problem. To solve the first and second problems, use Relax-and-Recover (ReaR), a disaster recovery and system migration utility.

Backup software creates backups. ReaR complements backup software by creating a rescue system. Booting the rescue system on a new hardware allows you to issue the rear recover command, which starts the recovery process. During this process, ReaR replicates the partition layout and filesystems, prompts for restoring user and system files from the backup created by backup software, and finally installs the boot loader. By default, the rescue system created by ReaR only restores the storage layout and the boot loader, but not the actual user and system files.

This chapter describes how to use ReaR.

34.1. Basic ReaR Usage

34.1.1. Installing ReaR

Install the rear package by running the following command as root:

~]# yum install rear

34.1.2. Configuring ReaR

ReaR is configured in the /etc/rear/local.conf file. Specify the rescue system configuration by adding these lines:

OUTPUT=output format
OUTPUT_URL=output location

Substitute output format with rescue system format, for example, ISO for an ISO disk image or USB for a bootable USB.

Substitute output location with where it will be put, for example, file:///mnt/rescue_system/ for a local filesystem directory or sftp://backup:password@192.168.0.0/ for an SFTP directory.

Example 34.1. Configuring Rescue System Format and Location

To configure ReaR to output the rescue system as an ISO image into the /mnt/rescue_system/ directory, add these lines to the /etc/rear/local.conf file:

OUTPUT=ISO
OUTPUT_URL=file:///mnt/rescue_system/

See section "Rescue Image Configuration" of the rear(8) man page for a list of all options.

34.1.3. Creating a Rescue System

The following example shows how to create a rescue system with verbose output:

~]# rear -v mkrescue
Relax-and-Recover 1.17.2 / Git
Using log file: /var/log/rear/rear-rhel68.log
mkdir: created directory `/var/lib/rear/output'
Creating disk layout
Creating root filesystem layout
TIP: To login as root via ssh you need to set up /root/.ssh/authorized_keys or SSH_ROOT_PASSWORD in your configuration file
Copying files and directories
Copying binaries and libraries
Copying kernel modules
Creating initramfs
Making ISO image
Wrote ISO image: /var/lib/rear/output/rear-rhel68.iso (82M)
Copying resulting files to file location

With the configuration from Example 34.1, “Configuring Rescue System Format and Location”, ReaR prints the above output. The last two lines confirm that the rescue system has been successfully created and copied to the configured backup location /mnt/rescue_system/. Because the system's host name is rhel-68, the backup location now contains directory rhel-68/ with the rescue system and auxiliary files:

~]# ls -lh /mnt/rescue_system/rhel68/
total 82M
-rw-------. 1 root root  202 May  9 11:46 README
-rw-------. 1 root root 160K May  9 11:46 rear.log
-rw-------. 1 root root  82M May  9 11:46 rear-rhel68.iso
-rw-------. 1 root root  275 May  9 11:46 VERSION

Transfer the rescue system to an external medium to not lose it in case of a disaster.

34.1.4. Scheduling ReaR

To schedule ReaR to regularly create a rescue system using the cron job scheduler, add the following line to the /etc/crontab file:

minute hour day_of_month month day_of_week root /usr/sbin/rear mkrescue

Substitute the above command with the cron time specification (described in detail in Section 27.1.4, “Configuring Cron Jobs”).

Example 34.2. Scheduling ReaR

To make ReaR create a rescue system at 22:00 every weekday, add this line to the /etc/crontab file:

0 22 * * 1-5 root /usr/sbin/rear mkrescue

34.1.5. Performing a System Rescue

To perform a restore or migration:

Boot the rescue system on the new hardware. For example, burn the ISO image to a DVD and boot from the DVD.
In the console interface, select the "Recover" option:
Figure 34.1. Rescue system: menu
You are taken to the prompt:
Figure 34.2. Rescue system: prompt
Warning
Once you have started recovery in the next step, it probably cannot be undone and you may lose anything stored on the physical disks of the system.
Run the rear recover command to perform the restore or migration. The rescue system then recreates the partition layout and filesystems:
Figure 34.3. Rescue system: running "rear recover"
Restore user and system files from the backup into the /mnt/local/ directory.
Example 34.3. Restoring User and System Files
In this example, the backup file is a tar archive created per instructions in Section 34.2.1.1, “Configuring the Internal Backup Method”. First, copy the archive from its storage, then unpack the files into /mnt/local/, then delete the archive:
```
~]# scp root@192.168.122.6:/srv/backup/rhel68/backup.tar.gz /mnt/local/
~]# tar xf /mnt/local/backup.tar.gz -C /mnt/local/
~]# rm -f /mnt/local/backup.tar.gz
```
The new storage has to have enough space both for the archive and the extracted files.
Verify that the files have been restored:
```
~]# ls /mnt/local/
```
Figure 34.4. Rescue system: restoring user and system files from the backup
Ensure that SELinux relabels the files on the next boot:
```
~]# touch /mnt/local/.autorelabel
```
Otherwise you may be unable to log in the system, because the /etc/passwd file may have the incorrect SELinux context.
Finish the recovery and reboot the system:
Figure 34.5. Rescue system: finishing recovery
ReaR will then reinstall the boot loader. Upon reboot, SELinux will relabel the whole filesystem.
Then you will be able to log in to the recovered system.