12.2. 设置作业调度程序
只有在启用了作业调度程序时，证书管理器才能执行作业。作业设置（如启用作业调度、设置频率和启用作业模块）可以通过证书Certificate Systemnbsp;System CA Console 或编辑
CS.cfg 文件来完成。
打开 Job Scheduler：
- 打开证书管理器控制台。
pkiconsole https://server.example.com:8443/ca - 在 Configuration 选项卡导航树中，单击 Job Scheduler。这将打开 General Settings 选项卡，其中显示作业调度程序当前是否已启用。
- 单击 Enable Jobs Schedule 复选框，以启用或禁用作业调度程序。禁用作业调度程序会关闭所有作业。
- 设置调度程序在 Check Frequency 字段中检查作业的频率。频率是作业调度程序守护进程线程的启动和调用符合 cron 规格的已配置作业的频率。默认情况下，它被设置为一分钟。注意输入此信息的窗口可能太小以查看输入信息。拖动证书管理器控制台的基石，以扩大整个窗口。
- 点 。
'%20d='M201.5%20305.5c-13.8%200-24.9-11.1-24.9-24.6%200-13.8%2011.1-24.9%2024.9-24.9%2013.6%200%2024.6%2011.1%2024.6%2024.9%200%2013.6-11.1%2024.6-24.6%2024.6zM504%20256c0%20137-111%20248-248%20248S8%20393%208%20256%20119%208%20256%208s248%20111%20248%20248zm-132.3-41.2c-9.4%200-17.7%203.9-23.8%2010-22.4-15.5-52.6-25.5-86.1-26.6l17.4-78.3%2055.4%2012.5c0%2013.6%2011.1%2024.6%2024.6%2024.6%2013.8%200%2024.9-11.3%2024.9-24.9s-11.1-24.9-24.9-24.9c-9.7%200-18%205.8-22.1%2013.8l-61.2-13.6c-3-.8-6.1%201.4-6.9%204.4l-19.1%2086.4c-33.2%201.4-63.1%2011.3-85.5%2026.8-6.1-6.4-14.7-10.2-24.1-10.2-34.9%200-46.3%2046.9-14.4%2062.8-1.1%205-1.7%2010.2-1.7%2015.5%200%2052.6%2059.2%2095.2%20132%2095.2%2073.1%200%20132.3-42.6%20132.3-95.2%200-5.3-.6-10.8-1.9-15.8%2031.3-16%2019.8-62.5-14.9-62.5zM302.8%20331c-18.2%2018.2-76.1%2017.9-93.6%200-2.2-2.2-6.1-2.2-8.3%200-2.5%202.5-2.5%206.4%200%208.6%2022.8%2022.8%2087.3%2022.8%20110.2%200%202.5-2.2%202.5-6.1%200-8.6-2.2-2.2-6.1-2.2-8.3%200zm7.7-75c-13.6%200-24.6%2011.1-24.6%2024.9%200%2013.6%2011.1%2024.6%2024.6%2024.6%2013.8%200%2024.9-11.1%2024.9-24.6%200-13.8-11-24.9-24.9-24.9z'/%3e%3c/svg%3e){kind=small}