このコンテンツは選択した言語では利用できません。
1.94. iscsi-initiator-utils
1.94.1. RHBA-2009:1099: bug fix update
Note
This update has already been released (prior to the GA of this release) as errata RHBA-2009:1099
The iscsi-initiator-utils package provides the server daemon for the iSCSI protocol, as well as the utility programs used to manage it. iSCSI is a protocol for distributed disk access using SCSI commands sent over Internet Protocol networks.
This updated iscsi-initiator-utils package fixes the following bug:
- attempting to log in to targets which used the iSCSI protocol's login redirect feature failed due to a coding error in the IPv6 address parser. This bug has been fixed in this updated package so that address parsing succeeds as expected, and logging in to targets over IPv6 is once again possible. (BZ#501737)
All users using IPv6 with LUN targets which employ login redirect, such as EqualLogic targets, should upgrade to this updated package, which resolves this issue.
1.94.2. RHBA-2009:1368: bug fix update
An updated iscsi-initiator-utils package that fixes various bugs and adds support for Chelsio and Broadcom iSCSI cards is now available
The iscsi package provides the server daemon for the iSCSI protocol, as well as the utility programs used to manage it. iSCSI is a protocol for distributed disk access using SCSI commands sent over Internet Protocol networks.
Bugs fixed and enhancements added in this updated package include:
- iscsi-initiator-utils now includes support for Broadcom bnx2 and bnx2x network interface cards. (BZ#442418)
- iscsi-initiator-utils has been rebased to upstream version 2.0-870. Among many other changes, this version supports the offload feature of Broadcom and Chelsio cards. Refer to the changelog included in the package for a full list of bug fixes and enhancements in this version. Section 5.1.2 of /usr/share/docs/iscsi-initiator-utils-$version/README contains instructions to set up ifaces for use with offload cards. (BZ#458203)
- the iscsi-initiator-utils packages place files in the /etc/iscsi directory but previously, did not list that directory for creation. The /etc/iscsi directory would therefore be created during the installation process, but would remain unowned. /etc/iscsi is now listed for creation and are therefore owned by iscsi-initiator-utils. (BZ#481807)
- when a user-space iSCSI tool invokes an option that is not supported in the kernel, the tool returns "Iferror -38". Previously, this error message was presented to users and could mislead them to think that a problem existed with their iSCSI configuration. The iSCSI tools no longer present this type of error to users and therefore do not create this potential misunderstanding. Note that certain combinations of new tools with old kernels might still present a related "-22" error. (BZ#497940)
- the iSCSI protocol allows targets to redirect initiators during the login phase. Previously, the code used by the iscsi initiator to parse IPv6 addresses contained faulty logic that caused it to fail to recognize IPv6 addresses as valid when redirected. As a consequence, when operating in an IPv6 environment, the initiator could not log into targets that use the login redirect feature, such as Dell EqualLogic targets. The initiator now parses IPv6 addresses correctly, enabling use of these targets in IPv6 environments. (BZ#500102)
- previously, the cxgb3i driver for Chelsio host bus adapters (HBAs) was not listed in the iscsi init script. Therefore, iscsi would not load this driver and therefore could not use the Chelsio HBAs that need this driver. The cxgb3i driver is now included in the iscsi init script, which enables the use of these devices. (BZ#505958)
- the iscsi code contained a bad cast of a data structure. This would lead to a segmentation fault while logging in or out of an iSCSI target. With the logic now corrected, these segmentation faults do not occur. (BZ#508782)
- iscsiadm obtains its information about the boot environment from the iSCSI boot firmware table (IBFT). However, this information does not include the target portal group tag (TPGT) associated with the boot target. Iscsiadm would assume that the relevant TPGT should be "1". In cases where this was correct, the boot process would continue as intended. In all other cases, iscsiadm would be unable to find the target necessary for the boot to proceed. This made it impossible to automate the installation of Red Hat Enterprise Linux in environments with multiple portals on targets and where the portal used for boot did not have TPGT=1. Iscsiadm no longer assumes a value for the TPGT for the boot portal and instead relies on the information that it finds in the /var/lib/iscsi record. This enables iscsiadm to find the correct target automatically, and therefore makes automated installations possible. (BZ#515806)
Users should upgrade to this updated package, which resolves these issues.