Ce contenu n'est pas disponible dans la langue sélectionnée.
16.8.2. Expanding a Disk Image
This section demonstrates a simple case of expanding a disk image:
- Locate the disk image to be resized. You can use the command
virsh dumpxml GuestNamefor a libvirt guest virtual machine. - Decide on how you wish to expand the guest virtual machine. Run
virt-df -handvirt-list-partitions -lhon the guest virtual machine disk, as shown in the following output:# virt-df -h /dev/vg_guests/RHEL6 Filesystem Size Used Available Use% RHEL6:/dev/sda1 98.7M 10.0M 83.6M 11% RHEL6:/dev/VolGroup00/LogVol00 6.8G 2.2G 4.3G 32% # virt-list-partitions -lh /dev/vg_guests/RHEL6 /dev/sda1 ext3 101.9M /dev/sda2 pv 7.9G
This example will demonstrate how to:
- Increase the size of the first (boot) partition, from approximately 100MB to 500MB.
- Increase the total disk size from 8GB to 16GB.
- Expand the second partition to fill the remaining space.
- Expand
/dev/VolGroup00/LogVol00to fill the new space in the second partition.
- Make sure the guest virtual machine is shut down.
- Rename the original disk as the backup. How you do this depends on the host physical machine storage environment for the original disk. If it is stored as a file, use the
mvcommand. For logical volumes (as demonstrated in this example), uselvrename:# lvrename /dev/vg_guests/RHEL6 /dev/vg_guests/RHEL6.backup
- Create the new disk. The requirements in this example are to expand the total disk size up to 16GB. Since logical volumes are used here, the following command is used:
# lvcreate -L 16G -n RHEL6 /dev/vg_guests Logical volume "RHEL6" created
- The requirements from step 2 are expressed by this command:
# virt-resize \ /dev/vg_guests/RHEL6.backup /dev/vg_guests/RHEL6 \ --resize /dev/sda1=500M \ --expand /dev/sda2 \ --LV-expand /dev/VolGroup00/LogVol00The first two arguments are the input disk and output disk.--resize /dev/sda1=500Mresizes the first partition up to 500MB.--expand /dev/sda2expands the second partition to fill all remaining space.--LV-expand /dev/VolGroup00/LogVol00expands the guest virtual machine logical volume to fill the extra space in the second partition.virt-resizedescribes what it is doing in the output:Summary of changes: /dev/sda1: partition will be resized from 101.9M to 500.0M /dev/sda1: content will be expanded using the 'resize2fs' method /dev/sda2: partition will be resized from 7.9G to 15.5G /dev/sda2: content will be expanded using the 'pvresize' method /dev/VolGroup00/LogVol00: LV will be expanded to maximum size /dev/VolGroup00/LogVol00: content will be expanded using the 'resize2fs' method Copying /dev/sda1 ... [#####################################################] Copying /dev/sda2 ... [#####################################################] Expanding /dev/sda1 using the 'resize2fs' method Expanding /dev/sda2 using the 'pvresize' method Expanding /dev/VolGroup00/LogVol00 using the 'resize2fs' method
- Try to boot the virtual machine. If it works (and after testing it thoroughly) you can delete the backup disk. If it fails, shut down the virtual machine, delete the new disk, and rename the backup disk back to its original name.
- Use
virt-dforvirt-list-partitionsto show the new size:# virt-df -h /dev/vg_pin/RHEL6 Filesystem Size Used Available Use% RHEL6:/dev/sda1 484.4M 10.8M 448.6M 3% RHEL6:/dev/VolGroup00/LogVol00 14.3G 2.2G 11.4G 16%
Resizing guest virtual machines is not an exact science. If
virt-resize fails, there are a number of tips that you can review and attempt in the virt-resize(1) man page. For some older Red Hat Enterprise Linux guest virtual machines, you may need to pay particular attention to the tip regarding GRUB.
