検索

このコンテンツは選択した言語では利用できません。

Chapter 8. Managing Snapshots

download PDF
Red Hat Gluster Storage Snapshot feature enables you to create point-in-time copies of Red Hat Gluster Storage volumes, which you can use to protect data. Users can directly access Snapshot copies which are read-only to recover from accidental deletion, corruption, or modification of the data.
Description

Figure 8.1. Snapshot Architecture

In the Snapshot Architecture diagram, Red Hat Gluster Storage volume consists of multiple bricks (Brick1 Brick2 etc) which is spread across one or more nodes and each brick is made up of independent thin Logical Volumes (LV). When a snapshot of a volume is taken, it takes the snapshot of the LV and creates another brick. Brick1_s1 is an identical image of Brick1. Similarly, identical images of each brick is created and these newly created bricks combine together to form a snapshot volume.
Some features of snapshot are:
  • Crash Consistency

    A crash consistent snapshot is captured at a particular point-in-time. When a crash consistent snapshot is restored, the data is identical as it was at the time of taking a snapshot.

    Note

    Currently, application level consistency is not supported.
  • Online Snapshot

    Snapshot is an online snapshot hence the file system and its associated data continue to be available for the clients even while the snapshot is being taken.

  • Quorum Based

    The quorum feature ensures that the volume is in a good condition while the bricks are down. If any brick that is down for a n way replication, where n <= 2 , quorum is not met. In a n-way replication where n >= 3, quorum is met when m bricks are up, where m >= (n/2 +1) where n is odd and m >= n/2 and the first brick is up where n is even. If quorum is not met snapshot creation fails.

  • Barrier

    To guarantee crash consistency some of the fops are blocked during a snapshot operation.

    These fops are blocked till the snapshot is complete. All other fops is passed through. There is a default time-out of 2 minutes, within that time if snapshot is not complete then these fops are unbarriered. If the barrier is unbarriered before the snapshot is complete then the snapshot operation fails. This is to ensure that the snapshot is in a consistent state.

Note

Taking a snapshot of a Red Hat Gluster Storage volume that is hosting the Virtual Machine Images is not recommended. Taking a Hypervisor assisted snapshot of a virtual machine would be more suitable in this use case.

8.1. Prerequisites

Before using this feature, ensure that the following prerequisites are met:
Recommended Setup

The recommended setup for using Snapshot is described below. In addition, you must ensure to read Chapter 20, Tuning for Performance for enhancing snapshot performance:
  • For each volume brick, create a dedicated thin pool that contains the brick of the volume and its (thin) brick snapshots. With the current thin-p design, avoid placing the bricks of different Red Hat Gluster Storage volumes in the same thin pool, as this reduces the performance of snapshot operations, such as snapshot delete, on other unrelated volumes.
  • The recommended thin pool chunk size is 256KB. There might be exceptions to this in cases where we have a detailed information of the customer's workload.
  • The recommended pool metadata size is 0.1% of the thin pool size for a chunk size of 256KB or larger. In special cases, where we recommend a chunk size less than 256KB, use a pool metadata size of 0.5% of thin pool size.
For Example

To create a brick from device /dev/sda1.
  1. Create a physical volume(PV) by using the pvcreate command.
    pvcreate /dev/sda1
    Use the correct dataalignment option based on your device. For more information, Section 20.2, “Brick Configuration”
  2. Create a Volume Group (VG) from the PV using the following command:
    vgcreate dummyvg /dev/sda1
  3. Create a thin-pool using the following command:
    # lvcreate --size 1T --thin dummyvg/dummypool --chunksize 256k --poolmetadatasize 16G  --zero n
    A thin pool of size 1 TB is created, using a chunksize of 256 KB. Maximum pool metadata size of 16 G is used.
  4. Create a thinly provisioned volume from the previously created pool using the following command:
    # lvcreate --virtualsize 1G --thin dummyvg/dummypool --name dummylv
  5. Create a file system (XFS) on this. Use the recommended options to create the XFS file system on the thin LV.
    For example,
    mkfs.xfs -f -i size=512 -n size=8192 /dev/dummyvg/dummylv
  6. Mount this logical volume and use the mount path as the brick.
    mount /dev/dummyvg/dummylv /mnt/brick1
Red Hat logoGithubRedditYoutubeTwitter

詳細情報

試用、購入および販売

コミュニティー

Red Hat ドキュメントについて

Red Hat をお使いのお客様が、信頼できるコンテンツが含まれている製品やサービスを活用することで、イノベーションを行い、目標を達成できるようにします。

多様性を受け入れるオープンソースの強化

Red Hat では、コード、ドキュメント、Web プロパティーにおける配慮に欠ける用語の置き換えに取り組んでいます。このような変更は、段階的に実施される予定です。詳細情報: Red Hat ブログ.

会社概要

Red Hat は、企業がコアとなるデータセンターからネットワークエッジに至るまで、各種プラットフォームや環境全体で作業を簡素化できるように、強化されたソリューションを提供しています。

© 2024 Red Hat, Inc.