Buscar

16.4. Static Routes and the Default Gateway

download PDF
Static routes are for traffic that must not, or should not, go through the default gateway. Routing is often handled by devices on the network dedicated to routing (although any device can be configured to perform routing). Therefore, it is often not necessary to configure static routes on Red Hat Enterprise Linux servers or clients. Exceptions include traffic that must pass through an encrypted VPN tunnel or traffic that should take a specific route for reasons of cost or security. The default gateway is for any and all traffic which is not destined for the local network and for which no preferred route is specified in the routing table. The default gateway is traditionally a dedicated network router.

Configuring Static Routes Using the Command Line

If static routes are required, they can be added to the routing table by means of the ip route add command and removed using the ip route del command. The more frequently used ip route commands take the following form:
ip route [ add | del | change | append | replace ] destination-address
See the ip-route(8) man page for more details on the options and formats.
Use the ip route command without options to display the IP routing table. For example:
~]$ ip route
default via 192.168.122.1 dev eth0  proto static  metric 1024 
192.168.122.0/24 dev ens9  proto kernel  scope link  src 192.168.122.107 
192.168.122.0/24 dev eth0  proto kernel  scope link  src 192.168.122.126
To add a static route to a host address, in other words to a single IP address, issue a command as root:
~]# ip route add 192.0.2.1 via 10.0.0.1 [dev ifname]
Where 192.0.2.1 is the IP address of the host in dotted decimal notation, 10.0.0.1 is the next hop address and ifname is the exit interface leading to the next hop.
To add a static route to a network, in other words to an IP address representing a range of IP addresses, issue the following command as root:
~]# ip route add 192.0.2.0/24 via 10.0.0.1 [dev ifname]
where 192.0.2.0 is the IP address of the destination network in dotted decimal notation and /24 is the network prefix. The network prefix is the number of enabled bits in the subnet mask. This format of network address slash network prefix length is sometimes referred to as classless inter-domain routing (CIDR) notation.
Static route configuration can be stored per-interface in a /etc/sysconfig/network-scripts/route-interface file. For example, static routes for the eth0 interface would be stored in the /etc/sysconfig/network-scripts/route-eth0 file. The route-interface file has two formats: ip command arguments and network/netmask directives. These are described below.
See the ip-route(8) man page for more information on the ip route command.

Configuring The Default Gateway

The default gateway is determined by the network scripts which parse the /etc/sysconfig/network file first and then the network interface ifcfg files for interfaces that are up. The ifcfg files are parsed in numerically ascending order, and the last GATEWAY directive to be read is used to compose a default route in the routing table.
The default route can thus be indicated by means of the GATEWAY directive and can be specified either globally or in interface-specific configuration files. Specifying the gateway globally has certain advantages in static networking environments, especially if more than one network interface is present. It can make fault finding simpler if applied consistently. There is also the GATEWAYDEV directive, which is a global option. If multiple devices specify GATEWAY, and one interface uses the GATEWAYDEV directive, that directive will take precedence. This option is not recommend as it can have unexpected consequences if an interface goes down and it can complicate fault finding.
Global default gateway configuration is stored in the /etc/sysconfig/network file. This file specifies gateway and host information for all network interfaces. For more information about this file and the directives it accepts, refer to Section 32.1.22, “/etc/sysconfig/network.
Red Hat logoGithubRedditYoutubeTwitter

Aprender

Pruebe, compre y venda

Comunidades

Acerca de la documentación de Red Hat

Ayudamos a los usuarios de Red Hat a innovar y alcanzar sus objetivos con nuestros productos y servicios con contenido en el que pueden confiar.

Hacer que el código abierto sea más inclusivo

Red Hat se compromete a reemplazar el lenguaje problemático en nuestro código, documentación y propiedades web. Para más detalles, consulte el Blog de Red Hat.

Acerca de Red Hat

Ofrecemos soluciones reforzadas que facilitan a las empresas trabajar en plataformas y entornos, desde el centro de datos central hasta el perímetro de la red.

© 2024 Red Hat, Inc.