Chapter 30. Kubernetes NMState

You can install the Kubernetes NMState Operator by using the web console. After it is installed, the Operator can deploy the NMState State Controller as a daemon set across all of the cluster nodes.

You can install the Kubernetes NMState Operator by using the OpenShift CLI (oc). After it is installed, the Operator can deploy the NMState State Controller as a daemon set across all of the cluster nodes.

You can monitor the policy status from the NodeNetworkConfigurationPolicy page. This page displays all the policies created in the cluster in a tabular format, with the following columns:

To find the desired policy, you can filter the list either based on enactment state by using the Filter option, or by using the search option.

You can create a policy by using either a form or YAML in the web console.

Create an interface on nodes in the cluster by applying a NodeNetworkConfigurationPolicy manifest to the cluster. The manifest details the requested configuration for the interface.

By default, the manifest applies to all nodes in the cluster. To add the interface to specific nodes, add the spec: nodeSelector parameter and the appropriate <key>:<value> for your node selector.

You can configure multiple nmstate-enabled nodes concurrently. The configuration applies to 50% of the nodes in parallel. This strategy prevents the entire cluster from being unavailable if the network connection fails. To apply the policy configuration in parallel to a specific portion of the cluster, use the maxUnavailable field.

Additional resources

A NodeNetworkConfigurationPolicy manifest describes your requested network configuration for nodes in the cluster. The node network policy includes your requested network configuration and the status of execution of the policy on the cluster as a whole.

When you apply a node network policy, a NodeNetworkConfigurationEnactment object is created for every node in the cluster. The node network configuration enactment is a read-only object that represents the status of execution of the policy on that node. If the policy fails to be applied on the node, the enactment for that node includes a traceback for troubleshooting.

You can remove an interface from one or more nodes in the cluster by editing the NodeNetworkConfigurationPolicy object and setting the state of the interface to absent.

Removing an interface from a node does not automatically restore the node network configuration to a previous state. If you want to restore the previous state, you will need to define that node network configuration in the policy.

If you remove a bridge or bonding interface, any node NICs in the cluster that were previously attached or subordinate to that bridge or bonding interface are placed in a down state and become unreachable. To avoid losing connectivity, configure the node NIC in the same policy so that it has a status of up and either DHCP or a static IP address.

Create a Linux bridge interface on nodes in the cluster by applying a NodeNetworkConfigurationPolicy manifest to the cluster.

The following YAML file is an example of a manifest for a Linux bridge interface. It includes samples values that you must replace with your own information.

apiVersion: nmstate.io/v1
kind: NodeNetworkConfigurationPolicy
metadata:
  name: br1-eth1-policy 1
spec:
  nodeSelector: 2
    kubernetes.io/hostname: <node01> 3
  desiredState:
    interfaces:
      - name: br1 4
        description: Linux bridge with eth1 as a port 5
        type: linux-bridge 6
        state: up 7
        ipv4:
          dhcp: true 8
          enabled: true 9
        bridge:
          options:
            stp:
              enabled: false 10
          port:
            - name: eth1 11

Create a VLAN interface on nodes in the cluster by applying a NodeNetworkConfigurationPolicy manifest to the cluster.

The following YAML file is an example of a manifest for a VLAN interface. It includes samples values that you must replace with your own information.

apiVersion: nmstate.io/v1
kind: NodeNetworkConfigurationPolicy
metadata:
  name: vlan-eth1-policy 1
spec:
  nodeSelector: 2
    kubernetes.io/hostname: <node01> 3
  desiredState:
    interfaces:
    - name: eth1.102 4
      description: VLAN using eth1 5
      type: vlan 6
      state: up 7
      vlan:
        base-iface: eth1 8
        id: 102 9

Update host network settings for Single Root I/O Virtualization (SR-IOV) network virtual functions (VF) in an existing cluster by applying a NodeNetworkConfigurationPolicy manifest.

You can apply a NodeNetworkConfigurationPolicy manifest to an existing cluster to complete the following tasks:

The following YAML file is an example of a manifest that defines QoS policies for a VF. This file includes samples values that you must replace with your own information.

apiVersion: nmstate.io/v1
kind: NodeNetworkConfigurationPolicy
metadata:
  name: qos 1
spec:
  nodeSelector: 2
    node-role.kubernetes.io/worker: "" 3
  desiredState:
    interfaces:
      - name: ens1f0 4
        description: Change QOS on VF0 5
        type: ethernet 6
        state: up 7
        ethernet:
         sr-iov:
           total-vfs: 3 8
           vfs:
           - id: 0 9
             max-tx-rate: 200 10

The following YAML file is an example of a manifest that creates a VLAN interface on top of a VF and adds it to a bonded network interface. It includes samples values that you must replace with your own information.

apiVersion: nmstate.io/v1
kind: NodeNetworkConfigurationPolicy
metadata:
  name: addvf 1
spec:
  nodeSelector: 2
    node-role.kubernetes.io/worker: "" 3
  maxUnavailable: 3
  desiredState:
    interfaces:
      - name: ens1f0v1 4
        type: ethernet
        state: up
      - name: ens1f0v1.477 5
        type: vlan
        state: up
        vlan:
          base-iface: ens1f0v1 6
          id: 477
      - name: bond0 7
        description: Add vf 8
        type: bond 9
        state: up 10
        link-aggregation:
          mode: active-backup 11
          options:
            primary: ens1f1v0.477 12
          port: 13
            - ens1f1v0.477
            - ens1f0v0.477
            - ens1f0v1.477 14

Create a bond interface on nodes in the cluster by applying a NodeNetworkConfigurationPolicy manifest to the cluster.

The following YAML file is an example of a manifest for a bond interface. It includes samples values that you must replace with your own information.

apiVersion: nmstate.io/v1
kind: NodeNetworkConfigurationPolicy
metadata:
  name: bond0-eth1-eth2-policy 1
spec:
  nodeSelector: 2
    kubernetes.io/hostname: <node01> 3
  desiredState:
    interfaces:
    - name: bond0 4
      description: Bond with ports eth1 and eth2 5
      type: bond 6
      state: up 7
      ipv4:
        dhcp: true 8
        enabled: true 9
      link-aggregation:
        mode: active-backup 10
        options:
          miimon: '140' 11
        port: 12
        - eth1
        - eth2
      mtu: 1450 13

Configure an Ethernet interface on nodes in the cluster by applying a NodeNetworkConfigurationPolicy manifest to the cluster.

The following YAML file is an example of a manifest for an Ethernet interface. It includes sample values that you must replace with your own information.

apiVersion: nmstate.io/v1
kind: NodeNetworkConfigurationPolicy
metadata:
  name: eth1-policy 1
spec:
  nodeSelector: 2
    kubernetes.io/hostname: <node01> 3
  desiredState:
    interfaces:
    - name: eth1 4
      description: Configuring eth1 on node01 5
      type: ethernet 6
      state: up 7
      ipv4:
        dhcp: true 8
        enabled: true 9

You can create multiple interfaces in the same node network configuration policy. These interfaces can reference each other, allowing you to build and deploy a network configuration by using a single policy manifest.

The following example YAML file creates a bond that is named bond10 across two NICs and VLAN that is named bond10.103 that connects to the bond.

apiVersion: nmstate.io/v1
kind: NodeNetworkConfigurationPolicy
metadata:
  name: bond-vlan 1
spec:
  nodeSelector: 2
    kubernetes.io/hostname: <node01> 3
  desiredState:
    interfaces:
    - name: bond10 4
      description: Bonding eth2 and eth3 5
      type: bond 6
      state: up 7
      link-aggregation:
        mode: balance-xor 8
        options:
          miimon: '140' 9
        port: 10
        - eth2
        - eth3
    - name: bond10.103 11
      description: vlan using bond10 12
      type: vlan 13
      state: up 14
      vlan:
         base-iface: bond10 15
         id: 103 16
      ipv4:
        dhcp: true 17
        enabled: true 18

Associate a Virtual Routing and Forwarding (VRF) instance with a network interface by applying a NodeNetworkConfigurationPolicy custom resource (CR).

By associating a VRF instance with a network interface, you can support traffic isolation, independent routing decisions, and the logical separation of network resources.

In a bare-metal environment, you can announce load balancer services through interfaces belonging to a VRF instance by using MetalLB. For more information, see the Additional resources section.

The following YAML file is an example of associating a VRF instance to a network interface. It includes samples values that you must replace with your own information.

apiVersion: nmstate.io/v1
kind: NodeNetworkConfigurationPolicy
metadata:
  name: vrfpolicy 1
spec:
  nodeSelector:
    vrf: "true" 2
  maxUnavailable: 3
  desiredState:
    interfaces:
      - name: ens4vrf 3
        type: vrf 4
        state: up
        vrf:
          port:
            - ens4 5
          route-table-id: 2 6

Create a Linux bridge interface on nodes in the cluster and transfer the static IP configuration of the NIC to the bridge by applying a single NodeNetworkConfigurationPolicy manifest to the cluster.

The following YAML file is an example of a manifest for a Linux bridge interface. It includes sample values that you must replace with your own information.

apiVersion: nmstate.io/v1
kind: NodeNetworkConfigurationPolicy
metadata:
  name: br1-eth1-copy-ipv4-policy 1
spec:
  nodeSelector: 2
    node-role.kubernetes.io/worker: ""
  capture:
    eth1-nic: interfaces.name=="eth1" 3
    eth1-routes: routes.running.next-hop-interface=="eth1"
    br1-routes: capture.eth1-routes | routes.running.next-hop-interface := "br1"
  desiredState:
    interfaces:
      - name: br1
        description: Linux bridge with eth1 as a port
        type: linux-bridge 4
        state: up
        ipv4: "{{ capture.eth1-nic.interfaces.0.ipv4 }}" 5
        bridge:
          options:
            stp:
              enabled: false
          port:
            - name: eth1 6
     routes:
        config: "{{ capture.br1-routes.routes.running }}"

The following snippet statically configures an IP address on the Ethernet interface:

# ...
    interfaces:
    - name: eth1
      description: static IP on eth1
      type: ethernet
      state: up
      ipv4:
        dhcp: false
        address:
        - ip: 192.168.122.250 1
          prefix-length: 24
        enabled: true
# ...

The following snippet ensures that the interface has no IP address:

# ...
    interfaces:
    - name: eth1
      description: No IP on eth1
      type: ethernet
      state: up
      ipv4:
        enabled: false
# ...

The following snippet configures an Ethernet interface that uses a dynamic IP address, gateway address, and DNS:

# ...
    interfaces:
    - name: eth1
      description: DHCP on eth1
      type: ethernet
      state: up
      ipv4:
        dhcp: true
        enabled: true
# ...

The following snippet configures an Ethernet interface that uses a dynamic IP address but does not use a dynamic gateway address or DNS:

# ...
    interfaces:
    - name: eth1
      description: DHCP without gateway or DNS on eth1
      type: ethernet
      state: up
      ipv4:
        dhcp: true
        auto-gateway: false
        auto-dns: false
        enabled: true
# ...

By default, the nmstate API stores DNS values globally as against storing them in a network interface. For certain situations, you must configure a network interface to store DNS values. To define a DNS configuration for a network interface, you must initially specify the dns-resolver section in the network interface’s YAML configuration file.

The following example shows a default situation that stores DNS values globally:

The following examples show situations that require configuring a network interface to store DNS values:

The following snippet configures a static route and a static IP on interface eth1.

dns-resolver:
  config:
# ...
interfaces:
  - name: eth1
    description: Static routing on eth1
    type: ethernet
    state: up
    ipv4:
      dhcp: false
      enabled: true
      address:
      - ip: 192.0.2.251 1
        prefix-length: 24
routes:
  config:
  - destination: 198.51.100.0/24
    metric: 150
    next-hop-address: 192.0.2.1 2
    next-hop-interface: eth1
    table-id: 254
# ...

For a cluster configured to query a bind9 DNS server, you can add the root-servers.net zone to a configuration file that contains at least one NS record. For example you can use the /var/named/named.localhost as a zone file that already matches this criteria.

If you are using dnsmasq as the DNS server, you can delegate resolution of the root-servers.net domain to another DNS server, for example, by creating a new configuration file that resolves root-servers.net using a DNS server that you specify.