Ricerca
SupportoConsoleSviluppatoriInizia una provaContatti

Questo contenuto non è disponibile nella lingua selezionata.

Chapter 8. Using the vSphere Problem Detector Operator

download PDF

8.1. About the vSphere Problem Detector Operator

The vSphere Problem Detector Operator checks clusters that are deployed on vSphere for common installation and misconfiguration issues that are related to storage.

The Operator runs in the openshift-cluster-storage-operator namespace and is started by the Cluster Storage Operator when the Cluster Storage Operator detects that the cluster is deployed on vSphere. The vSphere Problem Detector Operator communicates with the vSphere vCenter Server to determine the virtual machines in the cluster, the default datastore, and other information about the vSphere vCenter Server configuration. The Operator uses the credentials from the Cloud Credential Operator to connect to vSphere.

The Operator runs the checks according to the following schedule:

  • The checks run every 8 hours.
  • If any check fails, the Operator runs the checks again in intervals of 1 minute, 2 minutes, 4, 8, and so on. The Operator doubles the interval up to a maximum interval of 8 hours.
  • When all checks pass, the schedule returns to an 8 hour interval.

The Operator increases the frequency of the checks after a failure so that the Operator can report success quickly after the failure condition is remedied. You can run the Operator manually for immediate troubleshooting information.

8.2. Running the vSphere Problem Detector Operator checks

You can override the schedule for running the vSphere Problem Detector Operator checks and run the checks immediately.

The vSphere Problem Detector Operator automatically runs the checks every 8 hours. However, when the Operator starts, it runs the checks immediately. The Operator is started by the Cluster Storage Operator when the Cluster Storage Operator starts and determines that the cluster is running on vSphere. To run the checks immediately, you can scale the vSphere Problem Detector Operator to 0 and back to 1 so that it restarts the vSphere Problem Detector Operator.

Prerequisites

  • Access to the cluster as a user with the cluster-admin role.

Procedure

  1. Scale the Operator to 0: 

    $ oc scale deployment/vsphere-problem-detector-operator --replicas=0 \
    -n openshift-cluster-storage-operator

    If the deployment does not scale to zero immediately, you can run the following command to wait for the pods to exit: 

    $ oc wait pods -l name=vsphere-problem-detector-operator \
    --for=delete --timeout=5m -n openshift-cluster-storage-operator

  2. Scale the Operator back to 1: 

    $ oc scale deployment/vsphere-problem-detector-operator --replicas=1 \
    -n openshift-cluster-storage-operator

  3. Delete the old leader lock to speed up the new leader election for the Cluster Storage Operator: 

    $ oc delete -n openshift-cluster-storage-operator \
    cm vsphere-problem-detector-lock

Verification

  • View the events or logs that are generated by the vSphere Problem Detector Operator. Confirm that the events or logs have recent timestamps.

8.3. Viewing the events from the vSphere Problem Detector Operator

After the vSphere Problem Detector Operator runs and performs the configuration checks, it creates events that can be viewed from the command line or from the OpenShift Container Platform web console.

Procedure

  • To view the events by using the command line, run the following command: 

    $ oc get event -n openshift-cluster-storage-operator \
    --sort-by={.metadata.creationTimestamp}

    Example output

    16m     Normal    Started             pod/vsphere-problem-detector-operator-xxxxx         Started container vsphere-problem-detector
16m     Normal    Created             pod/vsphere-problem-detector-operator-xxxxx         Created container vsphere-problem-detector
16m     Normal    LeaderElection      configmap/vsphere-problem-detector-lock    vsphere-problem-detector-operator-xxxxx became leader

  • To view the events by using the OpenShift Container Platform web console, navigate to Home Events and select openshift-cluster-storage-operator from the Project menu.

8.4. Viewing the logs from the vSphere Problem Detector Operator

After the vSphere Problem Detector Operator runs and performs the configuration checks, it creates log records that can be viewed from the command line or from the OpenShift Container Platform web console.

Procedure

  • To view the logs by using the command line, run the following command: 

    $ oc logs deployment/vsphere-problem-detector-operator \
    -n openshift-cluster-storage-operator

    Example output

    I0108 08:32:28.445696       1 operator.go:209] ClusterInfo passed
I0108 08:32:28.451029       1 datastore.go:57] CheckStorageClasses checked 1 storage classes, 0 problems found
I0108 08:32:28.451047       1 operator.go:209] CheckStorageClasses passed
I0108 08:32:28.452160       1 operator.go:209] CheckDefaultDatastore passed
I0108 08:32:28.480648       1 operator.go:271] CheckNodeDiskUUID:<host_name> passed
I0108 08:32:28.480685       1 operator.go:271] CheckNodeProviderID:<host_name> passed

  • To view the Operator logs with the OpenShift Container Platform web console, perform the following steps:

    1. Navigate to Workloads Pods.
    2. Select openshift-cluster-storage-operator from the Projects menu.
    3. Click the link for the vsphere-problem-detector-operator pod.
    4. Click the Logs tab on the Pod details page to view the logs.

8.5. Configuration checks run by the vSphere Problem Detector Operator

The following tables identify the configuration checks that the vSphere Problem Detector Operator runs. Some checks verify the configuration of the cluster. Other checks verify the configuration of each node in the cluster.

Table 8.1. Cluster configuration checks
NameDescription

CheckDefaultDatastore

Verifies that the default datastore name in the vSphere configuration is short enough for use with dynamic provisioning.

If this check fails, you can expect the following:

  • systemd logs errors to the journal such as Failed to set up mount unit: Invalid argument.
  • systemd does not unmount volumes if the virtual machine is shut down or rebooted without draining all the pods from the node.

If this check fails, reconfigure vSphere with a shorter name for the default datastore.

CheckFolderPermissions

Verifies the permission to list volumes in the default datastore. This permission is required to create volumes. The Operator verifies the permission by listing the / and /kubevols directories. The root directory must exist. It is acceptable if the /kubevols directory does not exist when the check runs. The /kubevols directory is created when the datastore is used with dynamic provisioning if the directory does not already exist.

If this check fails, review the required permissions for the vCenter account that was specified during the OpenShift Container Platform installation.

CheckStorageClasses

Verifies the following:

  • The fully qualified path to each persistent volume that is provisioned by this storage class is less than 255 characters.
  • If a storage class uses a storage policy, the storage class must use one policy only and that policy must be defined.

CheckTaskPermissions

Verifies the permission to list recent tasks and datastores.

ClusterInfo

Collects the cluster version and UUID from vSphere vCenter.

Table 8.2. Node configuration checks
NameDescription

CheckNodeDiskUUID

Verifies that all the vSphere virtual machines are configured with disk.enableUUID=TRUE.

If this check fails, see the How to check 'disk.EnableUUID' parameter from VM in vSphere Red Hat Knowledgebase solution.

CheckNodeProviderID

Verifies that all nodes are configured with the ProviderID from vSphere vCenter. This check fails when the output from the following command does not include a provider ID for each node. 

$ oc get nodes -o custom-columns=NAME:.metadata.name,PROVIDER_ID:.spec.providerID,UUID:.status.nodeInfo.systemUUID

If this check fails, refer to the vSphere product documentation for information about setting the provider ID for each node in the cluster.

CollectNodeESXiVersion

Reports the version of the ESXi hosts that run nodes.

CollectNodeHWVersion

Reports the virtual machine hardware version for a node.

8.6. About the storage class configuration check

The names for persistent volumes that use vSphere storage are related to the datastore name and cluster ID.

When a persistent volume is created, systemd creates a mount unit for the persistent volume. The systemd process has a 255 character limit for the length of the fully qualified path to the VDMK file that is used for the persistent volume.

The fully qualified path is based on the naming conventions for systemd and vSphere. The naming conventions use the following pattern: 

/var/lib/kubelet/plugins/kubernetes.io/vsphere-volume/mounts/[<datastore>] 00000000-0000-0000-0000-000000000000/<cluster_id>-dynamic-pvc-00000000-0000-0000-0000-000000000000.vmdk
  • The naming conventions require 205 characters of the 255 character limit.
  • The datastore name and the cluster ID are determined from the deployment.
  • The datastore name and cluster ID are substituted into the preceding pattern. Then the path is processed with the systemd-escape command to escape special characters. For example, a hyphen character uses four characters after it is escaped. The escaped value is \x2d.
  • After processing with systemd-escape to ensure that systemd can access the fully qualified path to the VDMK file, the length of the path must be less than 255 characters.

8.7. Metrics for the vSphere Problem Detector Operator

The vSphere Problem Detector Operator exposes the following metrics for use by the OpenShift Container Platform monitoring stack.

Table 8.3. Metrics exposed by the vSphere Problem Detector Operator
NameDescription

vsphere_cluster_check_total

Cumulative number of cluster-level checks that the vSphere Problem Detector Operator performed. This count includes both successes and failures.

vsphere_cluster_check_errors

Number of failed cluster-level checks that the vSphere Problem Detector Operator performed. For example, a value of 1 indicates that one cluster-level check failed.

vsphere_esxi_version_total

Number of ESXi hosts with a specific version. Be aware that if a host runs more than one node, the host is counted only once.

vsphere_node_check_total

Cumulative number of node-level checks that the vSphere Problem Detector Operator performed. This count includes both successes and failures.

vsphere_node_check_errors

Number of failed node-level checks that the vSphere Problem Detector Operator performed. For example, a value of 1 indicates that one node-level check failed.

vsphere_node_hw_version_total

Number of vSphere nodes with a specific hardware version.

vsphere_vcenter_info

Information about the vSphere vCenter Server.

8.8. Additional resources

Red Hat logoGithubRedditYoutubeTwitter

Formazione

Prova, acquista e vendi

Community

Informazioni sulla documentazione di Red Hat

Aiutiamo gli utenti Red Hat a innovarsi e raggiungere i propri obiettivi con i nostri prodotti e servizi grazie a contenuti di cui possono fidarsi.

Rendiamo l’open source più inclusivo

Red Hat si impegna a sostituire il linguaggio problematico nel codice, nella documentazione e nelle proprietà web. Per maggiori dettagli, visita ilBlog di Red Hat.

Informazioni su Red Hat

Forniamo soluzioni consolidate che rendono più semplice per le aziende lavorare su piattaforme e ambienti diversi, dal datacenter centrale all'edge della rete.

© 2024 Red Hat, Inc.