第 5 章 Troubleshooting

1. Ignition configuration files are created.
2. The bootstrap machine boots and starts hosting the remote resources required for the master machines to boot.
3. The master machines fetch the remote resources from the bootstrap machine and finish booting.
4. The master machines use the bootstrap machine to form an etcd cluster.
5. The bootstrap machine starts a temporary Kubernetes control plane using the new etcd cluster.
6. The temporary control plane schedules the production control plane to the master machines.
7. The temporary control plane shuts down and passes control to the production control plane.
8. The bootstrap machine adds OpenShift Container Platform components into the production control plane.
9. The installation program shuts down the bootstrap machine.
10. The control plane sets up the worker nodes.
11. The control plane installs additional services in the form of a set of Operators.
12. The cluster downloads and configures remaining components needed for the day-to-day operation, including the creation of worker machines in supported environments.

Procedure

1. Check that the haproxy systemd service is active:

   $ ssh <user_name>@<load_balancer> systemctl status haproxy

2. Verify that the load balancer is listening on the required ports. The following example references ports 80, 443, 6443, and 22623.

   • For HAProxy instances running on Red Hat Enterprise Linux (RHEL) 6, verify port status by using the netstat command:

     $ ssh <user_name>@<load_balancer> netstat -nltupe | grep -E ':80|:443|:6443|:22623'

   • For HAProxy instances running on Red Hat Enterprise Linux (RHEL) 7 or 8, verify port status by using the ss command:

     $ ssh <user_name>@<load_balancer> ss -nltupe | grep -E ':80|:443|:6443|:22623'

     注意

     Red Hat recommends the ss command instead of netstat in Red Hat Enterprise Linux (RHEL) 7 or later. ss is provided by the iproute package. For more information on the ss command, see the Red Hat Enterprise Linux (RHEL) 7 Performance Tuning Guide.

3. Check that the wildcard DNS record resolves to the load balancer:

   $ dig <wildcard_fqdn> @<dns_server>

Procedure

1. Watch the installation log as the installation progresses:

   $ tail -f ~/<installation_directory>/.openshift_install.log

2. Monitor the bootkube.service journald unit log on the bootstrap node, after it has booted. This provides visibility into the bootstrapping of the first control plane. Replace <bootstrap_fqdn> with the bootstrap node’s fully qualified domain name:

   $ ssh core@<bootstrap_fqdn> journalctl -b -f -u bootkube.service

   注意

   The bootkube.service log on the bootstrap node outputs etcd connection refused errors, indicating that the bootstrap server is unable to connect to etcd on master nodes. After etcd has started on each master node and the nodes have joined the cluster, the errors should stop.

3. Monitor kubelet.service journald unit logs on master nodes, after they have booted. This provides visibility into master node agent activity.

   1. Monitor the logs using oc:

      $ oc adm node-logs --role=master -u kubelet

   2. If the API is not functional, review the logs using SSH instead. Replace <master-node>.<cluster_name>.<base_domain> with appropriate values:

      $ ssh core@<master-node>.<cluster_name>.<base_domain> journalctl -b -f -u kubelet.service

4. Monitor crio.service journald unit logs on master nodes, after they have booted. This provides visibility into master node CRI-O container runtime activity.

   1. Monitor the logs using oc:

      $ oc adm node-logs --role=master -u crio

   2. If the API is not functional, review the logs using SSH instead. Replace <master-node>.<cluster_name>.<base_domain> with appropriate values:

      $ ssh core@master-N.cluster_name.sub_domain.domain journalctl -b -f -u crio.service

Procedure

1. If you have access to the bootstrap node’s console, monitor the console until the node reaches the login prompt.

2. Verify the Ignition file configuration.

   • If you are hosting Ignition configuration files by using an HTTP server.

     1. Verify the bootstrap node Ignition file URL. Replace <http_server_fqdn> with HTTP server’s fully qualified domain name:

        $ curl -I http://<http_server_fqdn>:<port>/bootstrap.ign  1

        1

        The -I option returns the header only. If the Ignition file is available on the specified URL, the command returns 200 OK status. If it is not available, the command returns 404 file not found.

     2. To verify that the Ignition file was received by the bootstrap node, query the HTTP server logs on the serving host. For example, if you are using an Apache web server to serve Ignition files, enter the following command:

        $ grep -is 'bootstrap.ign' /var/log/httpd/access_log

        If the bootstrap Ignition file is received, the associated HTTP GET log message will include a 200 OK success status, indicating that the request succeeded.

     3. If the Ignition file was not received, check that the Ignition files exist and that they have the appropriate file and web server permissions on the serving host directly.

   • If you are using a cloud provider mechanism to inject Ignition configuration files into hosts as part of their initial deployment.

     1. Review the bootstrap node’s console to determine if the mechanism is injecting the bootstrap node Ignition file correctly.
3. Verify the availability of the bootstrap node’s assigned storage device.
4. Verify that the bootstrap node has been assigned an IP address from the DHCP server.

5. Collect bootkube.service journald unit logs from the bootstrap node. Replace <bootstrap_fqdn> with the bootstrap node’s fully qualified domain name:

   $ ssh core@<bootstrap_fqdn> journalctl -b -f -u bootkube.service

   注意

   The bootkube.service log on the bootstrap node outputs etcd connection refused errors, indicating that the bootstrap server is unable to connect to etcd on master nodes. After etcd has started on each master node and the nodes have joined the cluster, the errors should stop.

6. Collect logs from the bootstrap node containers.

   1. Collect the logs using podman on the bootstrap node. Replace <bootstrap_fqdn> with the bootstrap node’s fully qualified domain name:

      $ ssh core@<bootstrap_fqdn> 'for pod in $(sudo podman ps -a -q); do sudo podman logs $pod; done'

7. If the bootstrap process fails, verify the following.

   • You can resolve api.<cluster_name>.<base_domain> from the installation host.
   • The load balancer proxies port 6443 connections to bootstrap and master nodes. Ensure that the proxy configuration meets OpenShift Container Platform installation requirements.

Procedure

1. If you have access to the master node’s console, monitor the console until the node reaches the login prompt. During the installation, Ignition log messages are output to the console.

2. Verify Ignition file configuration.

   • If you are hosting Ignition configuration files by using an HTTP server.

     1. Verify the master node Ignition file URL. Replace <http_server_fqdn> with HTTP server’s fully qualified domain name:

        $ curl -I http://<http_server_fqdn>:<port>/master.ign  1

        1

        The -I option returns the header only. If the Ignition file is available on the specified URL, the command returns 200 OK status. If it is not available, the command returns 404 file not found.

     2. To verify that the Ignition file was received by the master node, query the HTTP server logs on the serving host. For example, if you are using an Apache web server to serve Ignition files:

        $ grep -is 'master.ign' /var/log/httpd/access_log

        If the master Ignition file is received, the associated HTTP GET log message will include a 200 OK success status, indicating that the request succeeded.

     3. If the Ignition file was not received, check that it exists on the serving host directly. Ensure that the appropriate file and web server permissions are in place.

   • If you are using a cloud provider mechanism to inject Ignition configuration files into hosts as part of their initial deployment.

     1. Review the master node’s console to determine if the mechanism is injecting the master node Ignition file correctly.
3. Check the availability of the master node’s assigned storage device.
4. Verify that the master node has been assigned an IP address from the DHCP server.

5. Determine master node status.

   1. Query master node status:

      $ oc get nodes

   2. If one of the master nodes does not reach a Ready status, retrieve a detailed node description:

      $ oc describe node <master_node>

      注意

      It is not possible to run oc commands if an installation issue prevents the OpenShift Container Platform API from running or if the kubelet is not running yet on each node:

6. Determine OpenShift Container Platform SDN status.

   1. Review sdn-controller, sdn, and ovs daemon set status, in the openshift-sdn namespace:

      $ oc get daemonsets -n openshift-sdn

   2. If those resources are listed as Not found, review pods in the openshift-sdn namespace:

      $ oc get pods -n openshift-sdn

   3. Review logs relating to failed OpenShift Container Platform SDN pods in the openshift-sdn namespace:

      $ oc logs <sdn_pod> -n openshift-sdn

7. Determine cluster network configuration status.

   1. Review whether the cluster’s network configuration exists:

      $ oc get network.config.openshift.io cluster -o yaml

   2. If the installer failed to create the network configuration, generate the Kubernetes manifests again and review message output:

      $ ./openshift-install create manifests

   3. Review the pod status in the openshift-network-operator namespace to determine whether the Cluster Network Operator (CNO) is running:

      $ oc get pods -n openshift-network-operator

   4. Gather network Operator pod logs from the openshift-network-operator namespace:

      $ oc logs pod/<network_operator_pod_name> -n openshift-network-operator

8. Monitor kubelet.service journald unit logs on master nodes, after they have booted. This provides visibility into master node agent activity.

   1. Retrieve the logs using oc:

      $ oc adm node-logs --role=master -u kubelet

   2. If the API is not functional, review the logs using SSH instead. Replace <master-node>.<cluster_name>.<base_domain> with appropriate values:

      $ ssh core@<master-node>.<cluster_name>.<base_domain> journalctl -b -f -u kubelet.service

      注意

      OpenShift Container Platform 4.5 cluster nodes running Red Hat Enterprise Linux CoreOS (RHCOS) are immutable and rely on Operators to apply cluster changes. Accessing cluster nodes using SSH is not recommended and nodes will be tainted as accessed. Before attempting to collect diagnostic data over SSH, review whether the data collected by running oc adm must gather and other oc commands is sufficient instead. However, if the OpenShift Container Platform API is not available, or the kubelet is not properly functioning on the target node, oc operations will be impacted. In such situations, it is possible to access nodes using ssh core@<node>.<cluster_name>.<base_domain>.

9. Retrieve crio.service journald unit logs on master nodes, after they have booted. This provides visibility into master node CRI-O container runtime activity.

   1. Retrieve the logs using oc:

      $ oc adm node-logs --role=master -u crio

   2. If the API is not functional, review the logs using SSH instead:

      $ ssh core@<master-node>.<cluster_name>.<base_domain> journalctl -b -f -u crio.service

10. Collect logs from specific subdirectories under /var/log/ on master nodes.

    1. Retrieve a list of logs contained within a /var/log/ subdirectory. The following example lists files in /var/log/openshift-apiserver/ on all master nodes:

       $ oc adm node-logs --role=master --path=openshift-apiserver

    2. Inspect a specific log within a /var/log/ subdirectory. The following example outputs /var/log/openshift-apiserver/audit.log contents from all master nodes:

       $ oc adm node-logs --role=master --path=openshift-apiserver/audit.log

    3. If the API is not functional, review the logs on each node using SSH instead. The following example tails /var/log/openshift-apiserver/audit.log:

       $ ssh core@<master-node>.<cluster_name>.<base_domain> sudo tail -f /var/log/openshift-apiserver/audit.log

11. Review master node container logs using SSH.

    1. List the containers:

       $ ssh core@<master-node>.<cluster_name>.<base_domain> sudo crictl ps -a

    2. Retrieve a container’s logs using crictl:

       $ ssh core@<master-node>.<cluster_name>.<base_domain> sudo crictl logs -f <container_id>

12. If you experience master node configuration issues, verify that the MCO, MCO endpoint, and DNS record are functioning. The Machine Config Operator (MCO) manages operating system configuration during the installation procedure. Also verify system clock accuracy and certificate validity.

    1. Test whether the MCO endpoint is available. Replace <cluster_name> with appropriate values:

       $ curl https://api-int.<cluster_name>:22623/config/master

    2. If the endpoint is unresponsive, verify load balancer configuration. Ensure that the endpoint is configured to run on port 22623.

    3. Verify that the MCO endpoint’s DNS record is configured and resolves to the load balancer.

       1. Run a DNS lookup for the defined MCO endpoint name:

          $ dig api-int.<cluster_name> @<dns_server>

       2. Run a reverse lookup to the assigned MCO IP address on the load balancer:

          $ dig -x <load_balancer_mco_ip_address> @<dns_server>

    4. Verify that the MCO is functioning from the bootstrap node directly. Replace <bootstrap_fqdn> with the bootstrap node’s fully qualified domain name:

       $ ssh core@<bootstrap_fqdn> curl https://api-int.<cluster_name>:22623/config/master

    5. System clock time must be synchronized between bootstrap, master, and worker nodes. Check each node’s system clock reference time and time synchronization statistics:

       $ ssh core@<node>.<cluster_name>.<base_domain> chronyc tracking

    6. Review certificate validity:

       $ openssl s_client -connect api-int.<cluster_name>:22623 | openssl x509 -noout -text

Procedure

1. Check the status of etcd pods.

   1. Review the status of pods in the openshift-etcd namespace:

      $ oc get pods -n openshift-etcd

   2. Review the status of pods in the openshift-etcd-operator namespace:

      $ oc get pods -n openshift-etcd-operator

2. If any of the pods listed by the previous commands are not showing a Running or a Completed status, gather diagnostic information for the pod.

   1. Review events for the pod:

      $ oc describe pod/<pod_name> -n <namespace>

   2. Inspect the pod’s logs:

      $ oc logs pod/<pod_name> -n <namespace>

   3. If the pod has more than one container, the preceding command will create an error, and the container names will be provided in the error message. Inspect logs for each container:

      $ oc logs pod/<pod_name> -c <container_name> -n <namespace>

3. If the API is not functional, review etcd pod and container logs on each master node by using SSH instead. Replace <master-node>.<cluster_name>.<base_domain> with appropriate values.

   1. List etcd pods on each master node:

      $ ssh core@<master-node>.<cluster_name>.<base_domain> sudo crictl pods --name=etcd-

   2. For any pods not showing Ready status, inspect pod status in detail. Replace <pod_id> with the pod’s ID listed in the output of the preceding command:

      $ ssh core@<master-node>.<cluster_name>.<base_domain> sudo crictl inspectp <pod_id>

   3. List containers related to a pod:

      $ ssh core@<master-node>.<cluster_name>.<base_domain> sudo crictl ps | grep '<pod_id>'

   4. For any containers not showing Ready status, inspect container status in detail. Replace <container_id> with container IDs listed in the output of the preceding command:

      $ ssh core@<master-node>.<cluster_name>.<base_domain> sudo crictl inspect <container_id>

   5. Review the logs for any containers not showing a Ready status. Replace <container_id> with the container IDs listed in the output of the preceding command:

      $ ssh core@<master-node>.<cluster_name>.<base_domain> sudo crictl logs -f <container_id>

      注意

      OpenShift Container Platform 4.5 cluster nodes running Red Hat Enterprise Linux CoreOS (RHCOS) are immutable and rely on Operators to apply cluster changes. Accessing cluster nodes using SSH is not recommended and nodes will be tainted as accessed. Before attempting to collect diagnostic data over SSH, review whether the data collected by running oc adm must gather and other oc commands is sufficient instead. However, if the OpenShift Container Platform API is not available, or the kubelet is not properly functioning on the target node, oc operations will be impacted. In such situations, it is possible to access nodes using ssh core@<node>.<cluster_name>.<base_domain>.

4. Validate primary and secondary DNS server connectivity from master nodes.

Procedure

1. Verify that the API server’s DNS record directs the kubelet on master nodes to https://api-int.<cluster_name>.<base_domain>:6443. Ensure that the record references the load balancer.
2. Ensure that the load balancer’s port 6443 definition references each master node.
3. Check that unique master node host names have been provided by DHCP.

4. Inspect the kubelet.service journald unit logs on each master node.

   1. Retrieve the logs using oc:

      $ oc adm node-logs --role=master -u kubelet

   2. If the API is not functional, review the logs using SSH instead. Replace <master-node>.<cluster_name>.<base_domain> with appropriate values:

      $ ssh core@<master-node>.<cluster_name>.<base_domain> journalctl -b -f -u kubelet.service

      注意

      OpenShift Container Platform 4.5 cluster nodes running Red Hat Enterprise Linux CoreOS (RHCOS) are immutable and rely on Operators to apply cluster changes. Accessing cluster nodes using SSH is not recommended and nodes will be tainted as accessed. Before attempting to collect diagnostic data over SSH, review whether the data collected by running oc adm must gather and other oc commands is sufficient instead. However, if the OpenShift Container Platform API is not available, or the kubelet is not properly functioning on the target node, oc operations will be impacted. In such situations, it is possible to access nodes using ssh core@<node>.<cluster_name>.<base_domain>.

5. Check for certificate expiration messages in the master node kubelet logs.

   1. Retrieve the log using oc:

      $ oc adm node-logs --role=master -u kubelet | grep -is 'x509: certificate has expired'

   2. If the API is not functional, review the logs using SSH instead. Replace <master-node>.<cluster_name>.<base_domain> with appropriate values:

      $ ssh core@<master-node>.<cluster_name>.<base_domain> journalctl -b -f -u kubelet.service  | grep -is 'x509: certificate has expired'

Procedure

1. If you have access to the worker node’s console, monitor the console until the node reaches the login prompt. During the installation, Ignition log messages are output to the console.

2. Verify Ignition file configuration.

   • If you are hosting Ignition configuration files by using an HTTP server.

     1. Verify the worker node Ignition file URL. Replace <http_server_fqdn> with HTTP server’s fully qualified domain name:

        $ curl -I http://<http_server_fqdn>:<port>/worker.ign  1

        1

        The -I option returns the header only. If the Ignition file is available on the specified URL, the command returns 200 OK status. If it is not available, the command returns 404 file not found.

     2. To verify that the Ignition file was received by the worker node, query the HTTP server logs on the HTTP host. For example, if you are using an Apache web server to serve Ignition files:

        $ grep -is 'worker.ign' /var/log/httpd/access_log

        If the worker Ignition file is received, the associated HTTP GET log message will include a 200 OK success status, indicating that the request succeeded.

     3. If the Ignition file was not received, check that it exists on the serving host directly. Ensure that the appropriate file and web server permissions are in place.

   • If you are using a cloud provider mechanism to inject Ignition configuration files into hosts as part of their initial deployment.

     1. Review the worker node’s console to determine if the mechanism is injecting the worker node Ignition file correctly.
3. Check the availability of the worker node’s assigned storage device.
4. Verify that the worker node has been assigned an IP address from the DHCP server.

5. Determine worker node status.

   1. Query node status:

      $ oc get nodes

   2. Retrieve a detailed node description for any worker nodes not showing a Ready status:

      $ oc describe node <worker_node>

      注意

      It is not possible to run oc commands if an installation issue prevents the OpenShift Container Platform API from running or if the kubelet is not running yet on each node.

6. Unlike master nodes, worker nodes are deployed and scaled using the Machine API Operator. Check the status of the Machine API Operator.

   1. Review Machine API Operator pod status:

      $ oc get pods -n openshift-machine-api

   2. If the Machine API Operator pod does not have a Ready status, detail the pod’s events:

      $ oc describe pod/<machine_api_operator_pod_name> -n openshift-machine-api

   3. Inspect machine-api-operator container logs. The container runs within the machine-api-operator pod:

      $ oc logs pod/<machine_api_operator_pod_name> -n openshift-machine-api -c machine-api-operator

   4. Also inspect kube-rbac-proxy container logs. The container also runs within the machine-api-operator pod:

      $ oc logs pod/<machine_api_operator_pod_name> -n openshift-machine-api -c kube-rbac-proxy

7. Monitor kubelet.service journald unit logs on worker nodes, after they have booted. This provides visibility into worker node agent activity.

   1. Retrieve the logs using oc:

      $ oc adm node-logs --role=worker -u kubelet

   2. If the API is not functional, review the logs using SSH instead. Replace <worker-node>.<cluster_name>.<base_domain> with appropriate values:

      $ ssh core@<worker-node>.<cluster_name>.<base_domain> journalctl -b -f -u kubelet.service

      注意

      OpenShift Container Platform 4.5 cluster nodes running Red Hat Enterprise Linux CoreOS (RHCOS) are immutable and rely on Operators to apply cluster changes. Accessing cluster nodes using SSH is not recommended and nodes will be tainted as accessed. Before attempting to collect diagnostic data over SSH, review whether the data collected by running oc adm must gather and other oc commands is sufficient instead. However, if the OpenShift Container Platform API is not available, or the kubelet is not properly functioning on the target node, oc operations will be impacted. In such situations, it is possible to access nodes using ssh core@<node>.<cluster_name>.<base_domain>.

8. Retrieve crio.service journald unit logs on worker nodes, after they have booted. This provides visibility into worker node CRI-O container runtime activity.

   1. Retrieve the logs using oc:

      $ oc adm node-logs --role=worker -u crio

   2. If the API is not functional, review the logs using SSH instead:

      $ ssh core@<worker-node>.<cluster_name>.<base_domain> journalctl -b -f -u crio.service

9. Collect logs from specific subdirectories under /var/log/ on worker nodes.

   1. Retrieve a list of logs contained within a /var/log/ subdirectory. The following example lists files in /var/log/sssd/ on all worker nodes:

      $ oc adm node-logs --role=worker --path=sssd

   2. Inspect a specific log within a /var/log/ subdirectory. The following example outputs /var/log/sssd/audit.log contents from all worker nodes:

      $ oc adm node-logs --role=worker --path=sssd/sssd.log

   3. If the API is not functional, review the logs on each node using SSH instead. The following example tails /var/log/sssd/sssd.log:

      $ ssh core@<worker-node>.<cluster_name>.<base_domain> sudo tail -f /var/log/sssd/sssd.log

10. Review worker node container logs using SSH.

    1. List the containers:

       $ ssh core@<worker-node>.<cluster_name>.<base_domain> sudo crictl ps -a

    2. Retrieve a container’s logs using crictl:

       $ ssh core@<worker-node>.<cluster_name>.<base_domain> sudo crictl logs -f <container_id>

11. If you experience worker node configuration issues, verify that the MCO, MCO endpoint, and DNS record are functioning. The Machine Config Operator (MCO) manages operating system configuration during the installation procedure. Also verify system clock accuracy and certificate validity.

    1. Test whether the MCO endpoint is available. Replace <cluster_name> with appropriate values:

       $ curl https://api-int.<cluster_name>:22623/config/worker

    2. If the endpoint is unresponsive, verify load balancer configuration. Ensure that the endpoint is configured to run on port 22623.

    3. Verify that the MCO endpoint’s DNS record is configured and resolves to the load balancer.

       1. Run a DNS lookup for the defined MCO endpoint name:

          $ dig api-int.<cluster_name> @<dns_server>

       2. Run a reverse lookup to the assigned MCO IP address on the load balancer:

          $ dig -x <load_balancer_mco_ip_address> @<dns_server>

    4. Verify that the MCO is functioning from the bootstrap node directly. Replace <bootstrap_fqdn> with the bootstrap node’s fully qualified domain name:

       $ ssh core@<bootstrap_fqdn> curl https://api-int.<cluster_name>:22623/config/worker

    5. System clock time must be synchronized between bootstrap, master, and worker nodes. Check each node’s system clock reference time and time synchronization statistics:

       $ ssh core@<node>.<cluster_name>.<base_domain> chronyc tracking

    6. Review certificate validity:

       $ openssl s_client -connect api-int.<cluster_name>:22623 | openssl x509 -noout -text

Procedure

1. Check that cluster Operators are all available at the end of an installation.

   $ oc get clusteroperators

2. If any Operators fail to become available, view Operator events:

   $ oc describe clusteroperator <operator_name>

3. Review Operator pod status within the Operator’s namespace:

   $ oc get pods -n <operator_namespace>

4. Obtain a detailed description for pods that do not have Running status:

   $ oc describe pod/<operator_pod_name> -n <operator_namespace>

5. Inspect pod logs:

   $ oc logs pod/<operator_pod_name> -n <operator_namespace>

6. When experiencing pod base image related issues, review base image status.

   1. Obtain details of the base image used by a problematic pod:

      $ oc get pod -o "jsonpath={range .status.containerStatuses[*]}{.name}{'\t'}{.state}{'\t'}{.image}{'\n'}{end}" <operator_pod_name> -n <operator_namespace>

   2. List base image release information:

      $ oc adm release info <image_path>:<tag> --commits

Procedure

1. Generate the commands that are required to obtain the installation logs from the bootstrap and control plane machines:

   • If you used installer-provisioned infrastructure, run the following command:

     $ ./openshift-install gather bootstrap --dir=<installation_directory> 1

     1

     installation_directory is the directory you specified when you ran ./openshift-install create cluster. This directory contains the OpenShift Container Platform definition files that the installation program creates.

     For installer-provisioned infrastructure, the installation program stores information about the cluster, so you do not specify the host names or IP addresses.

   • If you used infrastructure that you provisioned yourself, run the following command:

     $ ./openshift-install gather bootstrap --dir=<installation_directory> \ 1
         --bootstrap <bootstrap_address> \ 2
         --master <master_1_address> \ 3
         --master <master_2_address> \ 4
         --master <master_3_address>" 5

     1

     For installation_directory, specify the same directory you specified when you ran ./openshift-install create cluster. This directory contains the OpenShift Container Platform definition files that the installation program creates.

     2

     <bootstrap_address> is the fully qualified domain name or IP address of the cluster’s bootstrap machine.

     3 4 5

     For each control plane, or master, machine in your cluster, replace <master_*_address> with its fully qualified domain name or IP address.

     注意

     A default cluster contains three control plane machines. List all of your control plane machines as shown, no matter how many your cluster uses.

   Example output

   INFO Pulling debug logs from the bootstrap machine
   INFO Bootstrap gather logs captured here "<installation_directory>/log-bundle-<timestamp>.tar.gz"

   If you open a Red Hat support case about your installation failure, include the compressed logs in the case.